A.Packets are distributed across the ports in the channel based on both the source and destination MAC addresses.
B.Packets are distributed across the ports in the channel based on both the source and destination IP addresses.
C.Packets are balanced across the ports in the channel based first on the source MAC address， then on the destination MAC address， then on the IP address.
D.Packets are distributed across the access ports in the channel based first on the source IP address and then the destination IP addresses.
您可能感興趣的試卷
你可能感興趣的試題
A.network management
B.improving QoS
C.determining budget
D.reducing costs
E.increasing competitiveness
F.improving customer support
You work as a network engineer for. You study the exhibit carefully. Based on the output of the show command，
what can you determine regarding EIGRP routing being performed by the switch？ （）
Exhibit：
A.There are 20 neighbors in the EIGRP neigbor table.
B.EIGRP is running normally and receiving IPv4 routing updates.
C.The switch has not established any neighbor relationships. Further network testing and troubleshooting must be performed to determine the cause of the problem.
D.EIGRP status cannot be determined. The command show ip eigrp topology would determine the routing protocol status.
You work as a network engineer for . You study the exhibit carefully. Based upon the output shown，
what can you determine？（）
Exhibit：
A.VLAN 30 is not operational due to the fact that there are no packet or byte counts indicated.
B.The IP Cisco Express Forwarding configuration is capable of supporting IPv6.
C.Cisco Express Forwarding load balancing has been disabled.
D.SVI VLAN 30 connects directly to the 10.1.30.0/24 network due to a valid glean adjacency.
You work as a network engineer for. You study the exhibit carefully. Based on the configuration
shown，
which two statements are correct regarding this Layer 3 security configuration example？ （）
Exhibit：
A.Source IP and MAC filtering on VLANs 10 and 11 will occur.
B.The switch will drop the configured MAC and IP address source bindings and forward all other traffic.
C.DHCP snooping will be automatically enabled on the access VLANs.
D.IP Source Guard is enabled.
E.Static IP source binding can only be configured on a routed port.
You work as a network engineer for. You study the exhibit carefully. From the configuration sample shown of a Cisco Catalyst 3560 Series Switch，
what can you determine regarding Layer 3 routing functionality of the interface？（）
Exhibit：
A.The interface is configured correctly for Layer 3 routing capabilities.
B.The interface needs an additional configuration entry to enable IP routing protocols.
C.The interface subcommand ip routing is required to enable IP routing on the interface.
D.An SVI interface is required to enable IP routing for network 192.20.135.0.
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Which two statements are true when the extended system ID feature is enabled？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）