Refer to the exhibit. Which statement is true about the output？（）
A.The port on switch CAT1 is forwarding and sending BPDUs correctly.
B.The port on switch CAT1 is blocking and sending BPDUs correctly.
C.The port on switch CAT2 is forwarding and receiving BPDUs correctly.
D.The port on switch CAT2 is blocking and sending BPDUs correctly.
E.The port on switch CAT3 is forwarding and receiving BPDUs correctly.
F.The port on switch CAT3 is forwarding， sending， and receiving BPDUs correctly.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
What does the command channel-group 1 mode desirable do？ （）
A.enables LACP unconditionally
B.enables PAgP only if a PAgP device is detected
C.enables PAgP unconditionally
D.enables Etherchannel only
E.enables LACP only if a LACP device is detected
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA.
Which two statements are true about the possible result of attaching the second link？（）
A.The switch port attached to LinkB will not transistion to up.
B.One of the two switch ports attached to the hub will go into blocking mode when a BPDU is received.
C.Both switch ports attached to the hub will transition to the blocking state.
D.A heavy traffic load could cause BPDU transmissions to be blocked and leave a switching loop.
E.The switch port attached to LinkA will immediately transition to the blocking state.
A.All ports will temporarily transition to the learning state for a period equal to the max age timer plus the forward delay interval.
B.All ports will transition temporarily to the learning state for a period equal to the forward delay interval.
C.The default aging time for MAC address entries will be reduced for a period of the max age timer plus the forward delay interval.
D.The default hello time for configuration BDPUs will be reduced for the period of the max age timer.
A.The port immediately transitions to the Forwarding state.
B.The switch generates a Topology Change Notification （TCN） BPDU.
C.The port immediately transitions to the err-disable state.
D.The port becomes a normal STP switch port.
A.RSTP information is automatically aged out.
B.The port sends a TCN to the root bridge.
C.The port moves to listening state.
D.The port becomes a normal spanning tree port.
最新試題
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Refer to the exhibit. Which statement is true about the output？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）