You work as a network engineer for . You study the exhibit carefully. Based upon the output shown,
what can you determine?()
Exhibit:
A.VLAN 30 is not operational due to the fact that there are no packet or byte counts indicated.
B.The IP Cisco Express Forwarding configuration is capable of supporting IPv6.
C.Cisco Express Forwarding load balancing has been disabled.
D.SVI VLAN 30 connects directly to the 10.1.30.0/24 network due to a valid glean adjacency.
您可能感興趣的試卷
你可能感興趣的試題
You work as a network engineer for. You study the exhibit carefully. Based on the configuration
shown,
which two statements are correct regarding this Layer 3 security configuration example? ()
Exhibit:
A.Source IP and MAC filtering on VLANs 10 and 11 will occur.
B.The switch will drop the configured MAC and IP address source bindings and forward all other traffic.
C.DHCP snooping will be automatically enabled on the access VLANs.
D.IP Source Guard is enabled.
E.Static IP source binding can only be configured on a routed port.
You work as a network engineer for. You study the exhibit carefully. From the configuration sample shown of a Cisco Catalyst 3560 Series Switch,
what can you determine regarding Layer 3 routing functionality of the interface?()
Exhibit:
A.The interface is configured correctly for Layer 3 routing capabilities.
B.The interface needs an additional configuration entry to enable IP routing protocols.
C.The interface subcommand ip routing is required to enable IP routing on the interface.
D.An SVI interface is required to enable IP routing for network 192.20.135.0.
A new floor has been added to the enterprise campus network, providing client access for desktop PCs, laptops, and IP phones for employees and guests. During verification, a few desktop PCs have limited corporate access but not Internet access. Most other desktop PCs, all laptops, and IP phones are working correctly. Additional information indicates that the desktop PCs are obtaining IP host addresses from the DHCP server, which is intended for only the IP phones.
Where should troubleshooting about this connectivity issue be focused?()
A.DNS
B.first-hop redundancy protocol
C.DHCP server and options
D.VLAN mapping
E.client network configuration
F.routing protocols
A new building has been added to the enterprise campus network, providing client access for desktop PCs, laptops, and IP phones for employees and guests. During verification, only a few laptops using
wireless are reported to have problems, while other desktops, IP phones, and most other wireless laptops are fully operational. Additional information received about the problem indicates that, while the problematic wireless laptops cannot reach internal corporate websites, they can reach the Internet.
Where should troubleshooting about this connectivity issue be focused?()
A.client network configuration
B.VLAN mapping
C.routing protocols
D.first-hop redundancy protocol
You work as a network engineer for. You study the exhibit carefully. You have configured an interface to be an SVI for Layer 3 routing capabilities. Assuming that all VLANs have been correctly configured and based on the configuration example shown,
what can be determined? ()
Exhibit:
A.Interface gigabitethernet0/2 will be excluded from Layer 2 switching and enabled for Layer 3 routing.
B.The interface is missing IP configuration parameters; therefore, it will only function at Layer 2.
C.The command switchport autostate exclude should be entered in global configuration mode, not sub-interface mode, to enable a Layer 2 port to be configured for Layer 3 routing.
D.The configured port is excluded in the calculation of the status of the SVI.
最新試題
What two things will occur when an edge port receives a BPDU?()
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct, what will be true about Switch 15?()
Which three statements about STP timers are true?()
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?()
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?()
What must be the same to make multiple switches part of the same Multiple Spanning Tree (MST)?()
During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain, the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change?()
Which two statements are true when the extended system ID feature is enabled? ()