單項選擇題

You work as a network engineer for. You study the exhibit carefully. You have configured an interface to be an SVI for Layer 3 routing capabilities. Assuming that all VLANs have been correctly configured and based on the configuration example shown, 
what can be determined? ()
Exhibit:

A.Interface gigabitethernet0/2 will be excluded from Layer 2 switching and enabled for Layer 3 routing.
B.The interface is missing IP configuration parameters; therefore, it will only function at Layer 2.
C.The command switchport autostate exclude should be entered in global configuration mode, not sub-interface mode, to enable a Layer 2 port to be configured for Layer 3 routing.
D.The configured port is excluded in the calculation of the status of the SVI.


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題

You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have 
assigned that interface to VLAN 20. To check the status of the SVI, you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state. 
What must be true in an SVI configuration to bring the VLAN and line protocol up?()

A.The port must be physically connected to another Layer 3 device.
B.At least one port in VLAN 20 must be active.
C.The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D.Because this is a virtual interface, the operational status will always be in an "up/up" state.

2.單項選擇題What is true of standard access control lists when applied to an interface to control inbound or outbound traffic?()

A.The best match of the ACL entries will be used for granularity of control.
B.They use source IP information for matching operations.
C.They use source and destination IP information for matching operations.
D.They use source IP information along with protocol-type information for finer granularity of control.

3.單項選擇題When configuring a routed port on a Cisco multilayer switch, which of these is a required configuration task that you must perform to enable that port to function as a routed port? ()

A.Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
B.Enter the no switchport command to disable Layer 2 functionality at the interface level.
C.Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.
D.Routing is enabled by default on a multilayer switch, so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.

4.單項選擇題What benefit results from implementation of Layer 3 switching versus Layer 2 switching in a fully meshed campus network?()

A.ease of IP address assignment versus use of external routers
B.redundancy from trunking between distribution layer switches
C.provides first-hop redundancy to clients
D.allows inter-VLAN communication without requiring complexity of routing protocols

5.單項選擇題

You work as a network engineer for . You study the exhibit carefully.
 What best describes the Cisco IOS IP SLA command and output in the exhibit?()

A.verifies which operation types have been enabled for IP SLA source
B.verifies which operation types have been enabled for IP SLA responder
C.verifies which operation types are supported in software
D.verifies enabled operation types that are not running

最新試題

Refer to the exhibit. Which Virtual Router Redundancy Protocol (VRRP) statement is true about the roles of the master virtual router and the backup virtual router?()

題型:單項選擇題

Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about the STP process for VLAN 200 are true? ()

題型:多項選擇題

Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1? ()

題型:單項選擇題

Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()

題型:單項選擇題

Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half  duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()

題型:單項選擇題

DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()

題型:單項選擇題

Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?()

題型:單項選擇題

What two things will occur when an edge port receives a BPDU?()

題型:多項選擇題

Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()

題型:單項選擇題

Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain, the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change?()

題型:單項選擇題