A.Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
B.Enter the no switchport command to disable Layer 2 functionality at the interface level.
C.Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.
D.Routing is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
您可能感興趣的試卷
你可能感興趣的試題
A.ease of IP address assignment versus use of external routers
B.redundancy from trunking between distribution layer switches
C.provides first-hop redundancy to clients
D.allows inter-VLAN communication without requiring complexity of routing protocols
You work as a network engineer for . You study the exhibit carefully.
What best describes the Cisco IOS IP SLA command and output in the exhibit？（）
A.verifies which operation types have been enabled for IP SLA source
B.verifies which operation types have been enabled for IP SLA responder
C.verifies which operation types are supported in software
D.verifies enabled operation types that are not running
You work as a network engineer for. You study the exhibit carefully. Which of these is true based upon the output shown in the command？（）
Exhibit：
A.The port has security enabled and has shut down due to a security violation.
B.The port is operational and has reached its configured maximum allowed number of MAC addresses.
C.The port will allow access for 11 MAC addresses in addition to the 3 configured MAC addresses.
D.If the number of devices attempting to access the port exceeds 11， the port will shut down for 20 minutes， as configured.
A.PACLs can be applied in the inbound or outbound direction of a Layer 2 physical interface.
B.At Layer 2， a MAC address PACL will take precedence over any existing Layer 3 PACL.
C.When you apply a port ACL to a trunk port， the ACL filters traffic on all VLANs present on the trunk port.
D.PACLs are not supported on EtherChannel interfaces.
A.Configure the private VLAN port parameters.
B.Configure and map the secondary VLAN to the primary VLAN.
C.Disable IGMP snooping.
D.Set the VTP mode to transparent.
最新試題
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）