Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1.
What will be the result？（）
A.The command will be rejected by the switch.
B.Interfaces FastEthernet0/13 and FastEthernet0/14 will no longer be bundled.
C.Dynamic Trunking Protocol will be turned off on interfaces FastEthernet0/13 and FastEthernet0/14.
D.Interfaces FastEthernet0/13 and FastEthernet0/14 will only allow traffic from the native VLAN.
E.Interfaces FastEthernet0/13 and FastEthernet0/14 will continue to pass traffic for VLANs 88，100，360.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
What will happen when one more user is connected to interface FastEthernet 5/1？ （）
A.All secure addresses will age out and be removed from the secure address list. This will cause the security violation counter to increment.
B.The first address learned on the port will be removed from the secure address list and be replaced with the new address.
C.The interface will be placed into the error-disabled state immediately， and an SNMP trap notification will be sent.
D.The packets with the new source addresses will be dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
Refer to the exhibit. LACP has been configured on Switch1 as shown.
Which is the correct command set to configure LACP on Switch2？（）
A.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode auto
B.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode passive
C.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode desirable
D.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode on
Refer to the exhibit.
What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
A.ip routing
B.no ip routing
C.router eigrp 1
D.no router eigrp 1
E.mls qos
F.no mls qos
A.VLAN instance mapping and revision number
B.VLAN instance mapping and member list
C.VLAN instance mapping， revision number， and member list
D.VLAN instance mapping， revision number， member list， and timers
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct，
what will be true about Switch 15？（）
A.All ports will be in forwarding mode.
B.All ports in VLAN 10 will be in forwarding mode.
C.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.
最新試題
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Refer to the exhibit. Which statement is true about the output？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）