Refer to the exhibit. Router B is performing bidirectional redistribution between EIGRP an d OSPF.The network 10.100.1.0/24 should not be reachable from the 10.100.9.0/24 network. However, it needs to be reachable from any network within the EIGRP domain. All other networks should be seen in both domains. Which change to router B would accom plish these goals?（）
A. Under the EIGRP process, insert the distribute - list block_net_1 out ospf 1 command.
B. Under the OSPF process, insert the distribute - list block_net_1 in serial1/0 command.
C. Under the EIGRP process, insert the distribute - list block_net_1 in serial1/0 command.
D. Under the OSPF process, insert the distribute - list block_net_1 out eigrp 1 command.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. AS 65500 is not advertising the prefix 192.168.12.0/22 to its provider. AS 65500 is running OSPF as its IGP. Whi ch of the following additions to the configuration is most likely to solve the problem?（）
A. RouterA(config)#ip cef
B. RouterA(config)#ip route 192.168.12.0 255.255.255.252 null 0
C. RouterA(config - router)#ebgp multihop 1
D. RouterA(config - router)#re distribute ospf 1
E. RouterA(config - router)#neighbor 192.168.14.253 next - hop - self
F. RouterA(config - router)#neighbor 192.168.14.253 local - as 65500
RouterA#debug ip ospf events OSPF events debugging is on RouterA# 04:43:16: OSPF: Rcv pkt from 10.3.0.2, Ethernet0/1, area 0.0.0.1 mismatch area 0.0.0.2 in the header 04:43:19: OSPF: Rcv hello from 10.100.100.3 area 0 from Ethernet0/0 10.1.0.1 04:43:19: OSPF: End of hello processing Refer to the exhibits. What can be done to fix the problem?（）
A. Change router B E0/1 interface to area 0.
B. Change router A interface E0/1 to area 0.0.0.2.
C. Configure the E0/1 i nterfaces of router A and router B to be in area 0.
D. Shut down the E0/1 interfaces in router A and router B as OSPF does not allow "back doors" between areas.
E. Remove the E0/1 interfaces in router A and router B from the OSPF process. Use static rou tes to route data directly from router A to router B to avoid passing data through router C in area 0.
Refer to the exhibit. Router C was configured so that it could form an adja cency with three OSPF neighbors, one connected to each of its three physical interfaces. Which statement is correct about router C?（）
A. It is configured and functioning correctly as an OSPF internal router.
B. It is configured and functioning correc tly as an ABR attached to stub area 4.
C. It is configured and functioning correctly as an ASBR attached to external area 4.
D. It is configured and functioning correctly as an ABR attached to totally stubby area 4.
E. It is not configured correctly to function as specified.
A. Apply the area 4 stub command to all routers in the area
B. On the ABR, use the area 4 stub command with the no - summary keyword
C. On the ABR, specify a default cost for the area with the area default - cost command
D. On the ABR, use the default - information originate command to inject a default route into area 4
E. Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas
Your network has a mixture of Fast Ethernet and Gigabit Ethernet links. What needs t o be done to ensure optimal data routing when using OSPF?（）
A. Nothing. OSPF will determine the most optimal path for routing data by default.
B. Adjust the hello and dead timers for more rapid detection of link failures.
C. Increase the reference - bandw idth used to calculate the interface default metrics, on all routers in your network.
D. Set the priority values on every broadcast interface to ensure that the designated and backup designated routers are the routers with the most processor and memory resources.
最新試題
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following are true of both OSPFv2 and OSPFv3?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）