99久久久国产精品尤物免费,欧洲乱码伦视频免费

多項選擇題To make OSPF area 4 totally stubby, the following command was issued on the ABR in router configuration mode: area 4 stub.Which two things need to be done to finish making area 4 a totally stubby area?（）

A. Apply the area 4 stub command to all routers in the area
B. On the ABR, use the area 4 stub command with the no - summary keyword
C. On the ABR, specify a default cost for the area with the area default - cost command
D. On the ABR, use the default - information originate command to inject a default route into area 4
E. Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas

點擊查看答案

您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題 Your network has a mixture of Fast Ethernet and Gigabit Ethernet links. What needs t o be done to ensure optimal data routing when using OSPF?（）

A. Nothing. OSPF will determine the most optimal path for routing data by default.
B. Adjust the hello and dead timers for more rapid detection of link failures.
C. Increase the reference - bandw idth used to calculate the interface default metrics, on all routers in your network.
D. Set the priority values on every broadcast interface to ensure that the designated and backup designated routers are the routers with the most processor and memory resources.

點擊查看答案

2.多項選擇題 Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

A. RouterC(config - if)#ip ospf network broadcast   RouterD(config - if)#ip ospf network broadcast
B. RouterC(config - if)#ip ospf network point - to - point   RouterD(config - if)#ip ospf network point - to - point
C. RouterC(config - router)#neighbor 10.100. 100.4   RouterD(config - router)#neighbor 10.100.100.3
D. RouterC(config - router)#neighbor 10.255.255.254   RouterD(config - router)#neighbor 10.255.255.253

點擊查看答案

3.單項選擇題 Refer to the exhibit. What is the effect of the OSPF configuration on router B?（）

A. All interfaces will be in area 0
B. The router will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 1
C. The route r will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 2
D. The router will be an ABR with s1/0 in area 0, f0/0 in area 1, and f0/1 in area 2

點擊查看答案

4.單項選擇題 OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A.
What can you conclude about router A?（）

A. Only the router A loopback interface is parti cipating in the OSPF routing process
B. None of the router A interfaces are participating in the OSPF routing process
C. Router A is using the loopback interface IP address as its OSPF router ID
D. Router A does not have any reachable OSPF neighbors

點擊查看答案

5.單項選擇題 Refer to the exhibits. You are verifying your OSPF implementation, and it does not seem to be functioning properly. What can you conclude from the exhibit and the show running - configuration command output? （）

A. The OSPF areas are not configured correctly.
B. The wildcard masks for the 10.x .x.x networks are incorrect.
C. The 172.16.x.x networks need to be connected to area 0 using virtual links.
D. The 172.16.x.x networks are discontiguous. OSPF is automatically summarizing them to 172.16.0.0/16 and data is being "black holed."
E. There is not enough information to make a determination.

點擊查看答案