Your network has a mixture of Fast Ethernet and Gigabit Ethernet links. What needs t o be done to ensure optimal data routing when using OSPF?（）
A. Nothing. OSPF will determine the most optimal path for routing data by default.
B. Adjust the hello and dead timers for more rapid detection of link failures.
C. Increase the reference - bandw idth used to calculate the interface default metrics, on all routers in your network.
D. Set the priority values on every broadcast interface to ensure that the designated and backup designated routers are the routers with the most processor and memory resources.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）
A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast
B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point
C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3
D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
Refer to the exhibit. What is the effect of the OSPF configuration on router B?（）
A. All interfaces will be in area 0
B. The router will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 1
C. The route r will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 2
D. The router will be an ABR with s1/0 in area 0, f0/0 in area 1, and f0/1 in area 2
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A.
What can you conclude about router A?（）
A. Only the router A loopback interface is parti cipating in the OSPF routing process
B. None of the router A interfaces are participating in the OSPF routing process
C. Router A is using the loopback interface IP address as its OSPF router ID
D. Router A does not have any reachable OSPF neighbors
Refer to the exhibits. You are verifying your OSPF implementation, and it does not seem to be functioning properly. What can you conclude from the exhibit and the show running - configuration command output? （）
A. The OSPF areas are not configured correctly.
B. The wildcard masks for the 10.x .x.x networks are incorrect.
C. The 172.16.x.x networks need to be connected to area 0 using virtual links.
D. The 172.16.x.x networks are discontiguous. OSPF is automatically summarizing them to 172.16.0.0/16 and data is being "black holed."
E. There is not enough information to make a determination.
Refer to the exhibits. Router B should advertise the network co nnected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B. What is the probable cause of the problem?（）
A. An access list on router B is causing the 192.168.3.16/28 network to be denied
B. An access list on router B is causing the 192.168.3.32/28 network to be denied
C. The distribute list on router B is referencing a numbered access list that does not exist on router B
D. The d istribute list on router B is referencing the wrong interface
最新試題
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）