The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting showsand R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026：：1：1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026：：1：2/122
ipv6 ospf 6 area 0
Figure 3
What is the solution of the fault condition？（）
A.Add ipv6 ospf 6 area 0 under S0/0/0/0.23 on R2
B.Add ipv6 ospf 6 area 6 under s0/0/0/0.23 on R2
C.Remove IPv6 address from s0/0/0/0.23 on R2
D.Enable IPv6 routing on s0/0/0/0.23 on R2
您可能感興趣的試卷
你可能感興趣的試題
The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting shows and R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026：：1：1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026：：1：2/122
ipv6 ospf 6 area 0
Figure 3
The Fault Condition is related to which technology？（）
A.IPv6 Addressing
B.Route Redistribution
C.OSPFv3
D.RIPng
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is not able to reach the WebServer. Initial troubleshooting shows that DSW1 can ping the Fa0/1interface of R4 but not the s0/0/0/0.34 interface.
Configurationon DSW1
router eigrp 10
network 10.1.4.4 0.0.0.0
network 10.2.1.1 0.0.0.0
network 10.2.4.13 0.0.0.0
no auto-summary
Configurationon DSW2
router eigrp 10
network 10.1.4.8 0.0.0.0
network 10.2.2.1 0.0.0.0
network 10.2.4.14 0.0.0.0
no auto-summary
Configurationon R4
router eigrp 10
network 10.1.4.5 0.0.0.0
no auto-summary
redistribute ospf 1 metric 100 10 255 1 1500 route-map EIGRP_to_OSPF !
router ospf 1
network 10.1.1.8 0.0.0.0 area 34
redistribute eigrp 10 subnets!
route-map EIGRP→OSPF
match ip address 1!
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 209.0.0.0 0.255.255.255
What is the solution of the fault condition？（）
A.Remove the redistribute command from OSPF process on R4
B.Change the route-map name in the redistribute command under OSPF process to EIGRP→OSPF on R4
C.Change EIGRP AS to 1 on R4
D.Advertise 10.1.1.8/30 network in EIGRP on R4
最新試題
Which three statements accurately describe IOS Firewall configurations？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password？（）
Drag and drop each management protocol on the above to the correct category on the below.
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.
Which statement about PPPoA configuration is correct？（）