The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting showsand R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026：：1：1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026：：1：2/122
ipv6 ospf 6 area 0
Figure 3
On Which device is the fault condition located?（）
A.DSW1
B.DSW2
C.R2
D.R3
您可能感興趣的試卷
你可能感興趣的試題
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is not able to reach the WebServer. Initial troubleshooting shows that DSW1 can ping the Fa0/1interface of R4 but not the s0/0/0/0.34 interface.
Configurationon DSW1
router eigrp 10
network 10.1.4.4 0.0.0.0
network 10.2.1.1 0.0.0.0
network 10.2.4.13 0.0.0.0
no auto-summary
Configurationon DSW2
router eigrp 10
network 10.1.4.8 0.0.0.0
network 10.2.2.1 0.0.0.0
network 10.2.4.14 0.0.0.0
no auto-summary
Configurationon R4
router eigrp 10
network 10.1.4.5 0.0.0.0
no auto-summary
redistribute ospf 1 metric 100 10 255 1 1500 route-map EIGRP_to_OSPF !
router ospf 1
network 10.1.1.8 0.0.0.0 area 34
redistribute eigrp 10 subnets!
route-map EIGRP→OSPF
match ip address 1!
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 209.0.0.0 0.255.255.255
What is the solution of the fault condition？（）
A.Remove the redistribute command from OSPF process on R4
B.Change the route-map name in the redistribute command under OSPF process to EIGRP→OSPF on R4
C.Change EIGRP AS to 1 on R4
D.Advertise 10.1.1.8/30 network in EIGRP on R4
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is not able to reach the WebServer. Initial troubleshooting shows that DSW1 can ping the Fa0/1interface of R4 but not the s0/0/0/0.34 interface.
Configurationon DSW1
router eigrp 10
network 10.1.4.4 0.0.0.0
network 10.2.1.1 0.0.0.0
network 10.2.4.13 0.0.0.0
no auto-summary
Configurationon DSW2
router eigrp 10
network 10.1.4.8 0.0.0.0
network 10.2.2.1 0.0.0.0
network 10.2.4.14 0.0.0.0
no auto-summary
Configurationon R4
router eigrp 1
network 10.1.4.5 0.0.0.0
no auto-summary
redistribute ospf 1
What is the solution of the fault condition？（）
A.Change the EIGRP AS to 1 on DSW1
B.Change the routing protocol on DSW1 and DSW2 to OSPF
C.Change the EIGRP AS to 10 on R4
D.Advertise 10.1.1.8/30 network in EIGRP on R4
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is not able to reach the WebServer. Initial troubleshooting shows that DSW1 can ping the Fa0/1interface of R4 but not the s0/0/0/0.34 interface.
Configurationon DSW1
router eigrp 10
network 10.1.4.4 0.0.0.0
network 10.2.1.1 0.0.0.0
network 10.2.4.13 0.0.0.0
no auto-summary
Configurationon DSW2
router eigrp 10
network 10.1.4.8 0.0.0.0
network 10.2.2.1 0.0.0.0
network 10.2.4.14 0.0.0.0
no auto-summary
Configurationon R4
router eigrp 1
network 10.1.4.5 0.0.0.0
no auto-summary
redistribute ospf 1
The Fault Condition is related to which technology？（）
A.EIGRP
B.InterVLAN communication
C.OSPF
D.Switch to Switch Connectivity
最新試題
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
cisco ios command to interface dialer 0
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Study the exhibit carefully. The Cisco IOS IPsec High Availability （IPsec HA） Enhancementsfeature provides an infrastructure for reliable and secure networks to provide transparent availability of the VPN gateways - that is， Cisco IOS Software-based routers. What are the twooptions that are used to provide High Availability IPsec？（）
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）