On a standalone access point， client association using eap-cisco wireless （cisco-leap） is failing， but association using eap-peap is functioning.
What needs to be enabled on the standalone access point to correct this issue？（）
A.network eap
B.open authentication plus mac
C.open authentication plus eap
D.a shared key
您可能感興趣的試卷
你可能感興趣的試題
You have just finished aligning a cisco aironet 1400 series wireless bridge link using
installation mode. when you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem？（）
A.configure the bridge to force infrastructure devices to associate only to the ssid parameter.
B.enable passwords on both bridges.
C.configure the distance parameter value.
D.configure the proper channel.
A.ssids are not case-sensitive.
B.ssids must be listed in the same order in the adu as they are in the access point.
C.a maximum of three ssids may be configured.
D.ssids may have a maximum of 16 characters.
A.allows client traffic， captures data on all channels
B.allows client traffic， captures data on a single channel
C.allows no client traffic， captures data on all channels
D.allows no client traffic， captures data on a single channel
You are troubleshooting a one-way call problem with a cisco 7920 wireless ip phone on a standalone wlan.
What may have caused this problem？（）
A.the minimum data rate is not set to 11 mbps.
B.publicly secure packet forwarding is enabled.
C.the access point is set to the least congested channel.
D.an address resolution protocol has been disabled.
A.operations plan
B.operations assessment
C.security administration
D.system monitoring
E.operations implementation
F.incident management
最新試題
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）