Exhibit：
You work as a network administrator at.You study the exhibit carefully. Three different wireless groups of users （support， staff， guests） are permitted to access the wireless LAN.
Which security policy should be implemented for the users in the guests group？ （）
A.LEAP authentication
B.Primary SSID with open or no WEP authentication
C.Static WEP and authentication
D.Open authentication with WEP plus MAC authentication
您可能感興趣的試卷
你可能感興趣的試題
You work as a network administrator at， You have been asked to configure 802.1x port-based authentication. You notice that the client workstation is not compatible with 802.1x port-based authentication.
What supported authentication server should be chosen？（）
A.TACACS with LEAP extensions
B.RADIUS with EAP extensions
C.TACACS+
D.LDAP
You work as a network engineer for . You study the switch exhibit carefully.
Which two statements are true？ （）
Exhibit:
A.The trust boundary is not on this switch.
B.It is displaying the AutoQos configuration that was initially applied.
C.Interface Fa0/3 trusts allCoS values.
D.The switch does not trust theCoS values of a Cisco IP phone attached to port Fa0/3.
E.The show auto qos command shows the user-defined QoS settings.
F.The show auto qos command does not display user configuration changes currently in effect.
A.DAI intercept all ARP packets on untrusted ports
B.DAI determines the validity of an ARP packet based on the valid MAC address-to-IP address bindings stored in the DHCP Snooping database.
C.DAI is used to prevent against a DHCP Snooping attack.
D.DAI forwards all ARP packets received on a trusted interface without any checks.
E.DAI forwards all ARP packets on untrusted ports.
F.DAI determines the validity of an ARP packet based on the valid MAC address-to-IP address bindings stored in the CAM table.
A.Classifying and marking traffic should be done as close to the traffic source as possible.
B.Classifying and marking traffic should be done at the distribution layer.
C.Traffic is classified and marked as it travels through the network.
D.If untrusted traffic enters a switch， it can be marked with a new QoS value appropriate for the policy in place.
E.The trust boundary moves depending on the type of traffic entering the network.
Refer to the exhibit.
What problem is preventing users on VLAN 100 from pinging addresses on VLAN 200？（）
A.No default route on DLS1.
B.Encapsulation mismatch between switches.
C.Native VLAN mismatch.
D.Subinterfaces should be created on Fa0/7 and Fa0/8 on DLS1.
E.Trunking needs to be enabled.
F.The ip routing command is missing on DLS1.
最新試題
Which two statements are true when the extended system ID feature is enabled？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）