單項選擇題When an OSPF design is planned, which implementation can help a router not have memory resource issues?()

A. Have a backbone area (area 0) with 40 routers and use default routes to reach external destinations
B. Have a backbo ne area (area 0) with 4 routers and 30,000 external routes injected into OSPF
C. Have less OSPF areas to reduce the need for interarea route summarizations
D. Have multiple OSPF processes on each OSPF router. Example, router ospf 1, router ospf 2


您可能感興趣的試卷

你可能感興趣的試題

2.單項選擇題

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?()

A. All OSPF implementations must have at le ast one interface in area 0.
B. You are attempting to run in the broadcast mode over an NBMA interface.
C. Both routers are configured to function as a BDR; therefore, there is no DR router.
D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.
E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

3.單項選擇題You have just completed an OSPF implementation. While executing your verification plan, you determine that R1 is not able to establish full OSPF adjacency with R2. The show ip ospf neighbor comman d output on R1 shows that R2 is stuck in the INIT state. What could be the cause of this problem?()

A. DR and BDR election errors between R1 and R2.
B. The R2 router has not received the OSPF hello packets from the R1 router.
C. Mismatched interface ma ximum transmission unit (MTU) configuration between the R1 and R2.
D. Mismatched OSPF hello interval configuration between the R1 and R2
E. Corrupted LSAs exchanges between the R1 and R2.

4.單項選擇題

Refer to the exhibit. Looking at the topology diagram and the partial router configurations shown, which statement is true? ()

A.The NProuter has two OSPF neighbors in the "Full" adjacency state
B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds
C.The NProuter serial0/0 interface has been configured with an OSPF network type of "pointtopoint"
D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting
E.The "Mismatched" error is caus ed by the expiration of the OSPF timers

5.單項選擇題

Refer to the exhibit. A Boston company bought the asse ts of a New York company and is trying to route traffic between the two data networks using EIGRP over EoMPLS. As a network consultant, you were asked to verify the interoperability of the two networks. From the show ip route command output, what can yo u tell the customer about the traffic flow between the subnet in New York (172.16.8.0/24) and the subnets in Boston (172.16.16.0/24 and 10.10.16.0/24)?()

A. Traffic is flowing between the 172.16.8.0 subnet and subnets 172.16.16.0 and 10.10.16.0 and no configuration changes are needed.
B. Auto - summary must be disabled on N1 and B1 before traffic can flow between the 172.16.8.0 subnet and subnets 172.16.16.0 and 10.10.16.0.
C. Traffic will flow between the 172.16.8.0 subnet and 172.16.16.0 without any further configuration changes. However, auto - summary must be disabled on N1 and B1 before traffic can flow between the 172.16.8.0 subnet and the 10.10.16.0 subnet.
D. Auto - summary must be disabled on N1 and B1 before traffic can flow between the 172.16 .8.0 subnet and the 172.16.16.0 subnet. However, traffic will flow between the 172.16.8.0 subnet and 10.10.16.0 without any further configuration changes.

最新試題

Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()

題型:單項選擇題

The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1

題型:單項選擇題

Which of the following features work the same in both RIP- 2 and RIPng?()

題型:多項選擇題

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?()ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable

題型:單項選擇題

The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?()R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best

題型:多項選擇題

The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?()

題型:多項選擇題

Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?()

題型:多項選擇題

Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?()interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64

題型:單項選擇題

An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?()

題型:單項選擇題

Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?()

題型:單項選擇題