A. DR and BDR election errors between R1 and R2.
B. The R2 router has not received the OSPF hello packets from the R1 router.
C. Mismatched interface ma ximum transmission unit (MTU) configuration between the R1 and R2.
D. Mismatched OSPF hello interval configuration between the R1 and R2
E. Corrupted LSAs exchanges between the R1 and R2.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Looking at the topology diagram and the partial router configurations shown, which statement is true? （）
A.The NProuter has two OSPF neighbors in the "Full" adjacency state
B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds
C.The NProuter serial0/0 interface has been configured with an OSPF network type of "pointtopoint"
D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting
E.The "Mismatched" error is caus ed by the expiration of the OSPF timers
Refer to the exhibit. A Boston company bought the asse ts of a New York company and is trying to route traffic between the two data networks using EIGRP over EoMPLS. As a network consultant, you were asked to verify the interoperability of the two networks. From the show ip route command output, what can yo u tell the customer about the traffic flow between the subnet in New York (172.16.8.0/24) and the subnets in Boston (172.16.16.0/24 and 10.10.16.0/24)?（）
A. Traffic is flowing between the 172.16.8.0 subnet and subnets 172.16.16.0 and 10.10.16.0 and no configuration changes are needed.
B. Auto - summary must be disabled on N1 and B1 before traffic can flow between the 172.16.8.0 subnet and subnets 172.16.16.0 and 10.10.16.0.
C. Traffic will flow between the 172.16.8.0 subnet and 172.16.16.0 without any further configuration changes. However, auto - summary must be disabled on N1 and B1 before traffic can flow between the 172.16.8.0 subnet and the 10.10.16.0 subnet.
D. Auto - summary must be disabled on N1 and B1 before traffic can flow between the 172.16 .8.0 subnet and the 172.16.16.0 subnet. However, traffic will flow between the 172.16.8.0 subnet and 10.10.16.0 without any further configuration changes.
Refer to the exhibit. A Boston company bought th e assets of a New York company and is trying to route traffic between the two data networks using EIGRP. The show command output shows that traffic will not flow between the networks. As a network consultant, you were asked to modify the configuration a nd certify the interoperability of the two networks. For traffic to flow from subnet 172.16.8.0/24 to the 172.16.16.0/24 subnet, which configuration change do you recommend?（）
A. Turn off autosummarization on routers N1 and B1.
B. Add IP summary addre sses to the Internet - pointing interfaces of routers N1 and B1.
C. Turn off autosummarization on routers N2 and B2.
D. Add wildcard masks to the network commands on routers N2 and B2.
Refer to the exhibit.The actual speed of the serial links between R2 and R3 are 256 kb/s and 512k b/s respectively. When configuring EIGRP on routers R2 and R3, the network administrator configured the bandwidth of both serial interfaces to 512 kb/s. What will be the effect?（）
A. EIGRP will overutilize the 512 kb/s link.
B. The interface "delay" value used in the EIGRP metric calculation will be inaccurate on the 256k b/s serial interface.
C. The amount of bandwidth used for EIGRP routing protocol traffic on the 256 kb/s link can become excessive.
D. EIGRP can load balance between the two serial links only if the variance is set to 2 or higher.
E. Unequal cost load balancing will be disabled.
最新試題
Which of the following answers lists a multicast IPv6 address?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1