You want to configure a switched internetwork with multiple VLANs as shown above.
Which of the following commands should you issue on SwitchA for the port connected to SwitchB？ （）
A. switchport mode trunk
B. switchport access vlan 5
C. switchport mode access vlan 5
D. switchport trunk native vlan 5
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
Which of the following should you do to configure the IP phone to override the priority of the data packets it receives from the host？ （）
A. Issue the mls qos trust cos command on the switch port connected to the IP phone.
B. Issue the switchport priority extend cos command on the switch port connected to the IP phone.
C. Issue the switchport priority extend cos command on the IP phone.
D. Issue the mls qos trust cos command on the IP phone.
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows：
R1#configure terminal
R1（config）#interface fa0/0
R1（config-if）#ip address 10.10.0.5 255.255.255.0
R1（config-if）#standby 1 priority 150
R1（config-if）#standby preempt delay minimum 50
R1（config-if）#standby 1 track interface fa0/2 15
R1（config-if）#standby 1 ip 10.10.0.20
Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）
A. The HSRP priority for router R1 will increase to 200.
B. Router R1 will become the standby router if the priority drops below 50.
C. The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.
D. Router R1 will wait 50 seconds before attempting to preempt the active router.
Routers R1 and R2 are configured for HSRP as shown below：
Router R1：
interface ethernet 0
ip address 20.6.2.1 255.255.255.0
standby 35 ip 20.6.2.21
standby 35 priority 100
interface ethernet 1
ip address 20.6.1.1.2 255.255.255.0
standby 34 ip 20.6.1.21
Router R2：
interface ethernet 0
ip address 20.6.2.2 255.255.255.0
standby 35 ip 20.6.2.21
interface ethernet 1
ip address 20.6.1.1.1 255.255.255.0
standby 34 ip 20.6.1.21
standby 34 priority 100
You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very
frequent HSRP group state transitions.
What is the most likely cause of this？ （）
A. physical layer issues
B. no spanning tree loops
C. use of non-default HSRP timers
D. failure to set the command standby 35 preempt
Exhibit
Which command will ensure that Company2 will be the primary router for traffic using the gateway address of 172.16.15.20？ （）
A. On R2 add the command standby 1 priority 80
B. On R1 add the command standby 1 priority 110
C. On R1 add the command standby 1 priority 80
D. On R2 remove the command standby 1 preempt
Refer to the exhibit. What statement is true based upon the configuration of router R1 and router R2？（）
A. Router R2 will become the master for Virtual Router 1， and router R1 will become the backup for Virtual Router 2.
B. Router R1 will become the master for Virtual Router 1， and router R2 will become the backup for Virtual Router 2.
C. Router R1 will become the active virtual gateway.
D. Router R2 will become the active virtual gateway.
E. The hello and hold timers are incompatible with OSPF type 5 LSAs.
F. The hello and hold timers are incompatible with multi-homed BGP.
最新試題
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which three statements about STP timers are true？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Which two statements about the various implementations of STP are true？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）