Refer to the exhibit. Based upon the debug output that is shown，
which three statements about HSRP are true？（）
A. The router with IP address 172.16.11.111 haspreempt configured.
B. The final active router is the router with IP address 172.16.11.111.
C. The router with IP address 172.16.11.112 has nonpreempt configured.
D. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address 172.16.11.111.
E. The router with IP address 172.16.11.112 is using default HSRP priority.
F. The IP address 172.16.11.115 is the virtual HSRP IP address.
您可能感興趣的試卷
你可能感興趣的試題
A. independent of SSO
B. NSF combined with SSO enables supervisor engine load balancing
C. supported by RIPv2， OSPF， IS-IS， and EIGRP
D. supports IPv4 and IPv6 multicast
E. prevents route flapping
F. dependent on FIB tables
pany has a Catalyst 6500 and you need to configure redundancy between the supervisor modules. With route processor redundancy （RPR+）， the redundant supervisor engine is fully initialized and configured， which shortens the switchover time if the active supervisor engine fails.
Which three statements are true about the RPR + operations when the redundant supervisor engine switched over the failed primary supervisor engine？ （）
A. Static IP routes are maintained across a switchover because they are configured from entries in the configuration file.
B. Information about dynamic routing states， maintained on the active supervisor engine， is synchronized to the redundant supervisor engine and is transferred during the switchover.
C. Information about dynamic routing states， maintained on the active supervisor engine， is not synchronized to the redundant supervisor engine and is lost on switchover.
D. The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routed traffic is interrupted until route tables reconverge.
E. Static IP routes are cleared across a switchover and recreated from entries in the configuration file on the redundant supervisor engine.
F. The Forwarding Information Base （FIB） tables are maintained during the switchover. As a result， routed traffic continues without any interruption when the failover occurs.
Refer to the exhibit.
What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100？ （）
A. Only if both tracked objects are up will this router will be available as an AVF for group 1.
B. Only if the state of both tracked objects goes down will this router release its status as an AVF for group 1.
C. If both tracked objects go down and then one comes up， but the other remains down， this router will be available as an AVF for group 1.
D. This configuration is incorrect and will not have any effect on GLBP operation.
E. If the state of one tracked object goes down then this router will release its status as an AVF for group 1.
Refer to the exhibit. GLBP has been configured on the network. When the interface serial0/0/1 on router R1 goes down，
how is the traffic coming from Host1 handled？ （）
A. The traffic coming from Host2 is forwarded through router R2 with no disruption. The traffic from Host1 is dropped due to the disruption of the load balancing feature configured for the glbp group.
B. The traffic coming from both hosts is temporarily interrupted while the switchover to make R2 active occurs.
C. The traffic coming from Host2 is forwarded through router R2 with no disruption. Host1 sendsan ARP request to resolve the MAC address for the new virtual gateway.
D. The traffic coming from Host1 and Host2 is forwarded through router R2 with no disruption.
Refer to the exhibit.
What is the configuration an example of？ （）
A. GLBP weighting
B. default AVF and AVG configuration
C. GLBP MD5 authentication
D. GLBP text authentication
E. GLBP timer manipulation
最新試題
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）