Refer to the exhibit. GLBP has been configured on the network. When the interface serial0/0/1 on router R1 goes down，
how is the traffic coming from Host1 handled？ （）
A. The traffic coming from Host2 is forwarded through router R2 with no disruption. The traffic from Host1 is dropped due to the disruption of the load balancing feature configured for the glbp group.
B. The traffic coming from both hosts is temporarily interrupted while the switchover to make R2 active occurs.
C. The traffic coming from Host2 is forwarded through router R2 with no disruption. Host1 sendsan ARP request to resolve the MAC address for the new virtual gateway.
D. The traffic coming from Host1 and Host2 is forwarded through router R2 with no disruption.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
What is the configuration an example of？ （）
A. GLBP weighting
B. default AVF and AVG configuration
C. GLBP MD5 authentication
D. GLBP text authentication
E. GLBP timer manipulation
Refer to the exhibit.
Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
A. Router A is the master virtual router， and Router B is the backup virtual router. When Router A fails， Router B will become the master virtual router. When Router A recovers， Router B will maintain the role of master virtual router.
B. Router B is the master virtual router， and Router A is the backup virtual router. When Router B fails， Router A will become the master virtual router. When Router B recovers， it will regain the master virtual router role.
C. Router A is the master virtual router， and Router B is the backup virtual router. When Router A fails， Router B will become the master virtual router. When Router A recovers， it will regain the master virtual router role.
D. Router B is the master virtual router， and Router A is the backup virtual router. When Router B fails， Router A will become the master virtual router. When Router B recovers， Router A will maintain the role of master virtual router.
Exhibit：
Exhibit：
You work as a network engineer at Company. You study the exhibit carefully. Which GLBP device hosts receive the MAC address assignment？（）
A. R1
B. R2
C. The AVG
D. The AVF
E. None of the other alternatives apply
On a 3550 EMI switch，
which three types of interfaces can be used to configure HSRP？ （）
A. Loopback interface
B. SVI interfac
C. Routed port
D. Access port
E. EtherChannel port channel
F. BVI interface
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails？ （）
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
最新試題
What is the configured priority value of the Vlan105’s group on DS2 ？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. Which statement is true about the output？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）