Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure.
Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D. All routers configured for HSRP load balancing must be configured with the same priority.
E. Routers configured for HSRP must belong to only one group per HSRP interface.
您可能感興趣的試卷
你可能感興趣的試題
You want to implement router redundancy in the Company network using the best method available.
Which protocol specified by RFC 2281 provides network redundancy for IP networks， ensuring that user traffic immediately and transparently recovers from first-hop failures in network edge devices or access circuits？（）
A. ICMP
B. IRDP
C. HSRP
D. STP
E. None of the other alternatives apply
pany uses GLBP to provide for router redundancy in the network.
Which describes the default load balancing scheme used by the Gateway Load Balancing Protocol （GLBP）？（）
A. Per host basis using a strict priority scheme
B. Per session using a round-robin scheme
C. Per session using a strict priority scheme
D. Per GLBP group using a strict priority scheme
E. Per host basis using a round-robin scheme
F. Per GLBP group using a round-robin scheme
HSRP has been configured between two Company devices.
Which of the following describe reasons for deploying HSRP？ （）
A. HSRP provides redundancy and fault tolerance
B. HSRP allows one router to automatically assume the function of the second router if the second router fails
C. HSRP allows one router to automatically assume the function of the second router if the second router starts
D. HSRP provides redundancy and load balancing
You want to implement a high availability network using two Cisco routers. You also want to ensure that the stat of the WAN interfaces can be tracked in doing so.
Which router redundancy protocol cannot be configured for interface tracking？ （）
A. GLBP
B. HSRP
C. RPR
D. VRRP
E. SLB
F. RPR+
G. None of the other alternatives apply
You need to configure two Company routers for high availability.
Which protocol enables a group of routers to form a single virtual router and use the real IP address of a router as the gateway address？ （）
A. HSRP
B. IRDP
C. Proxy ARP
D. GLBP
E. VRRP
F. None of the other alternatives apply
最新試題
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. Which statement is true about the output？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Which three statements about STP timers are true？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）