The Company network administrator has entered the "auto qos voip cisco-phone" command on switch R1.
What does this command do？（）
A.It disables the trust boundary feature because the switch knows a Cisco IP phone is attached.
B.The switch assigns a CoS value of 5 to incoming packets.
C.If a Cisco IP phone is attached and removed， the switch continues to trust the CoS values as long as the switch is not rebooted.
D.It turns on STP to see if a Cisco IP phone is attached.
E.If a Cisco IP phone is attached， the switch trusts the CoS.
F.None of the other alternatives apply.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
Which three statements are true about the voice VLAN configuration of the Catalyst switch？ （）
A.The packet priority received from a device that is connected to the phone will be unmodified.
B.The packet priority received from a device that is connected to the phone will be overridden.
C.Incoming CoS values in packets from the connected phone will be left unmodified.
D.Packets without aCoS value that is set by the phone will be set to a value of 5.
E.Incoming CoS values in packets from the connected phone will be reset to a value of 5.
F.Packets without aCoS value that is set by the phone will be set to the default CoS value.
The Cisco AutoQoS feature is being used throughout the Company VOIP network.
Which three statements about this feature are true？（）
A.The "mls qos" global configuration command must be entered before configuring AutoQoS.
B.CEF must be enabled.
C.The "no auto qos voip" command is used to disable Cisco AutoQos and revoke all configurations generated by Cisco AutoQos.
D.CDP must be enabled.
E.SNMP must be enabled.
Refer to the exhibit.
What is the effect on the trust boundary of configuring the command mls qos trust cos on the switch port that is connected to the IP phone？（）
A.Effectively the trust boundary has been moved to the IP phone.
B.RTP will be used to negotiate aCoS value based upon bandwidth utilization on the link.
C.The switch is rewriting packets it receives from the IP phone and determining theCoS value.
D.The switch will no longer tag incoming voice packets and will trust the distribution layer switch to set theCoS.
E.The host is now establishing theCoS value and has effectively become the trust boundary.
Refer to the exhibit.
Which switch interface configuration command would automatically configure quality of service （QoS） for voice over IP （VoIP） within a QoS domain？ （）
A.switchport priority extend trust
B.mls qos trust
C.switchport priority extend cos 7
D.auto qos voip cisco-phone
Refer to the exhibit. A trunk link is connected between switch A_SW and switch D_SW. Based on the configuration shown in the exhibit，
how would the traffic coming from the switch A_SW be managed？（）
A.The trunk port Fa0/1 on switch A_SW will trust allCoS values on the frames coming from the IP phone.
B.The trunk port Fa0/1 on switch A_SW will trust allCoS values on the frames received on the IP phone.
C.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames coming from port Fa0/1 on A_SW.
D.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames received on the A_SW switch port Fa0/4.
E.The trunk port Fa0/1 on switch D_SW will trust allCoS values on the frames received on the IP phone port.
最新試題
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Refer to the exhibit. Which statement is true about the output？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）