A.Antenna power is a relative value reference to dBi
B.LWAPP allows encrypted communications between lightweight access points and WLANcontrollers.
C.Characteristics of antennas are directionality， gain， and polarization
D.Power over Ethernet （PoE） is only available when a WLAN controller is integrated into thenetwork
E.The WLAN solution Engine （WLSE） is used to control lightweight access points
F.One of the advantages of the lightweight WLAN solution is that the devices act indepently
您可能感興趣的試卷
你可能感興趣的試題
Network topology exhibit：
In this WLAN segment， what are three requirements for configuring these Aironet access points（APs） that will allow for all wireless clients to work without service interruption while roaming fromaccess point to access point？（）
All access points should be configured....
A....with a unique IP subnet range
B....with identical SSIDs
C....within the same IP subnet
D....with the same guest mode SSID
E....only with the native VLAN
F....with the native VLAN
A.association request/response， probe request/response， authentication request/response
B.association request/response， authentication request/response， probe request/response
C.probe request/response， authentication request/response， association request/response
D.probe request/response， association request/response， authentication request/response
E.None of the other alternatives apply
Exhibit：
In this scenario the signal transmitted from the AP is reflected off a wall， resulting in multipathinterference at the client end （ClientA）. Which of the following statements is true？（）
A.The transmitted signal from the AP arrives at the client at slightly different times resulting inphase shifting
B.Multipath interference can be solved by using dual antennas
C.If signal 2 is close to 360 degrees out of phase with signal 1， the result is essentially zero signalor a dead spot in the WLAN
D.Multipath interference is less of an issue when using a DSSS technology because multipath isfrequency selective
E.If signal 1 is in phase with signal 2， the result is essentially zero signal or a dead spot in theWLAN
F.None of the other alternatives apply
Exhibit：
You work as a network technician. Please study the exhibit carefully. In this wireless network， theLAP （lightweight access point） attempts to register to a WLC （Wireless LAN Controller）. What kindof message is transmitted？（）
A.The lightweight access point will send Layer 2 and Layer 3 Lightweight Access Point （LWAPP）mode discovery request messages at the same time
B.The lightweight access point will send Layer 3 Lightweight Access Point （LWAPP） modediscovery request messages only
C.The lightweight access point will send Layer 2 Lightweight Access Point （LWAPP） mode discovery request messages. If the attempt fails， the LAP will try Layer 3 LWAPP WLC discovery
D.The lightweight access point will send Layer 2 Lightweight Access Point （LWAPP） modediscovery request messages only
A.Switchover ensures that Layer 2 through Layer 4 traffic is not interrupted
B.Redundancy requires BGP， OSPF， EIGRP， or IS-IS
C.Redundancy provides fast supervisor switchover for all Cisco Catalyst 6500 series switches
D.Switchover can be caused by clock synchronization failure between supervisors
最新試題
Router NetworkTut is configured as shown below：Given the above configuration， which statement is true？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
cisco ios command to interface dialer 0
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）