Network topology exhibit：
In this WLAN segment， what are three requirements for configuring these Aironet access points（APs） that will allow for all wireless clients to work without service interruption while roaming fromaccess point to access point？（）
All access points should be configured....
A....with a unique IP subnet range
B....with identical SSIDs
C....within the same IP subnet
D....with the same guest mode SSID
E....only with the native VLAN
F....with the native VLAN
您可能感興趣的試卷
你可能感興趣的試題
A.association request/response， probe request/response， authentication request/response
B.association request/response， authentication request/response， probe request/response
C.probe request/response， authentication request/response， association request/response
D.probe request/response， association request/response， authentication request/response
E.None of the other alternatives apply
Exhibit：
In this scenario the signal transmitted from the AP is reflected off a wall， resulting in multipathinterference at the client end （ClientA）. Which of the following statements is true？（）
A.The transmitted signal from the AP arrives at the client at slightly different times resulting inphase shifting
B.Multipath interference can be solved by using dual antennas
C.If signal 2 is close to 360 degrees out of phase with signal 1， the result is essentially zero signalor a dead spot in the WLAN
D.Multipath interference is less of an issue when using a DSSS technology because multipath isfrequency selective
E.If signal 1 is in phase with signal 2， the result is essentially zero signal or a dead spot in theWLAN
F.None of the other alternatives apply
Exhibit：
You work as a network technician. Please study the exhibit carefully. In this wireless network， theLAP （lightweight access point） attempts to register to a WLC （Wireless LAN Controller）. What kindof message is transmitted？（）
A.The lightweight access point will send Layer 2 and Layer 3 Lightweight Access Point （LWAPP）mode discovery request messages at the same time
B.The lightweight access point will send Layer 3 Lightweight Access Point （LWAPP） modediscovery request messages only
C.The lightweight access point will send Layer 2 Lightweight Access Point （LWAPP） mode discovery request messages. If the attempt fails， the LAP will try Layer 3 LWAPP WLC discovery
D.The lightweight access point will send Layer 2 Lightweight Access Point （LWAPP） modediscovery request messages only
A.Switchover ensures that Layer 2 through Layer 4 traffic is not interrupted
B.Redundancy requires BGP， OSPF， EIGRP， or IS-IS
C.Redundancy provides fast supervisor switchover for all Cisco Catalyst 6500 series switches
D.Switchover can be caused by clock synchronization failure between supervisors
A.independent of SSO
B.NSF combined with SSO enables supervisor engine load balancing
C.supported by RIPv2， OSPF， IS-IS， and EIGRP
D.supports IPv4 and IPv6 multicast
E.prevents route flapping
F.dependent on FIB tables
最新試題
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
cisco ios command to interface dialer 0
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）