A.show spantree backbonefast
B.show spantree statistics
C.show spantree uplinkfast
D.show spantree blockedports
E.show spantree portstate
F.show spantree portvlancost
您可能感興趣的試卷
你可能感興趣的試題
The network is displayed in the diagram below：
You use the following information for switch SWA：
Port Mode Encapsulation Status Native VLAN
fa0/1 desirable n-802.1q trunking 5
Port VLANs is allowed on trunk
fa0/ 1 1-100， 102-1005
Port VLANs is owned and active in management domain
fa0/1 1-6. 8-100， 102-115， 197-999， 1002-1005
Port VLANs in spanning tree forwarding state and not pruned
fa0/1 1-6， 8-100， 102-105， 108-999， 1002-1005
SW users in VLAN 107 complain that they are unable to gain access to the resources through theSW1 router.
What is the cause of this problem？（）
A.VLAN 107 is not configured on the trunk
B.VLAN 107 does not exist on switch SWA
C.VTP is pruning VLAN 107
D.Spanning tree is not enabled on VLAN 107
E.None of the other alternatives apply
A.Combine all the VLAN spanning trees into a single spanning tree
B.Set forward delay and max-age timers to the maximum possible values
C.None of the choices
D.Change the router VTP server mode
E.Disable the root bridge
Exhibit
SW1#show spanning-tree vlan 200
VLAN200
Spanning tree enabled protocol iee
eRoot ID Priority 32968
Address 000c.ce29.ef00
Cost 19
Port 2 （FastEthernet0/2）
Hello time 10 Sec Max Age 20 sec Forward Delay 30 sec
Bridge ID Priority 32968 （priority 32768 sys-id-ext 200）
Address 000c.ce2a.4180
Hello Time 2 sec Max Age 20 Sec Forward Delay 15 sec
Interface Role Sts Cost PrioNbr Type
Fa0/2 Root FWD 19 128.2 P2p
Fa0/3 Altn BLK 19 128.3 P2p
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statementsabout the STP process for VLAN 200 are true？（）
A.BDPUs will be sent out every two seconds
B.The time spent in the listening state will be 30 seconds
C.The time spent in the learning state will be 15 seconds
D.The maximum length of time that the BPDU information will be saved is 30 seconds
E.This switch is the root bridge for VLAN 200
F.BPDUs will be sent out every 10 seconds
A.hello timer
B.BPDU timer
C.Forward_delay timer
D.Max_age timer
E.Dead timer
F.Wait timer
Given the above diagram and assuming that STP is enabled on all switch devices， which twostatements are true？（）
A.DSW11willbe elected the root bridge
B.DSW12 will be elected the root bridge
C.ASW13 will be elected the root bridge
D.P3/1 will be elected the nondesignated port
E.P2/2 will be elected the nondesignated port
F.P3/2 will be elected the nondesignated port
最新試題
Network Topology Exhibit：Configuration Exhibit：NET（config）# access-list 112 deny icmp any any echo logNET（config）# access-list 112 deny imp any any redirect logNET（config）# access-list 112 deny icmp any any mask-request logNET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET（config）# interface Fa0/1NET（config-if）# ip access-group 112 inYou work as a network administrator at networkTut.com， study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
cisco ios command to interface dialer 0
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Which statement about PPPoA configuration is correct？（）
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.