The switched LAN is shown below：
Study the exhibit above carefully. Switch SW5 is configured as the root switch for VLAN 10 but notfor VLAN 20. If the STP configuration is correct， what will be true about Switch SW5？（）
A.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standbymode
B.All ports will be in forwarding mode
C.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blockingmode
D.All ports in VLAN 10 will be in forwarding mode
E.None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
A.IEEE 802.10
B.Misconfigured NIC
C.User configuration
D.IEEE 802.1Q
E.None of the other alternatives apply
A VTP domain has six active VLANs. Without notice， all VLANs except VLAN1 fail. Just prior tothe failure， Switch2 was added to the network.
Which three issues on Switch2 could be the cause？（）
A.Switch2 is configured for only VLAN1
B.Switch2 is a VTP server in a different domain
C.Switch2 is a VTP server in the Company domain
D.Switch2 is not a VTP domain.
E.Switch2 has a lower VTP configuration revision number than the current VTP revision
F.Switch2 has a higher VTP configuration revision number than the current VTP revision
A.Physical management of the switch
B.Logical management of the switch
C.In-band management of the switch
D.Out-of-band management of the switch
A.Reload the active VLAN configuration
B.Clear the affected port and bring it up again
C.Explicitly set the trunk for the VLAN to be on
D.Remove all the VLANs set
A.The link is using IEEE 802.1Q protocol
B.The link is using IEEE 802.1E protocol
C.Spanning tree is disabled
D.Not enough information to determine
E.The native VLAN information is identical at each end of the link
F.The native VLAN information is different at each end of the link
最新試題
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Which statement about PPPoA configuration is correct？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below