A.Spanning Tree Protocol （STP）
B.Delay reduction
C.Hot Standby Routing Protocol （HSRP）
D.Dynamic routing protocols
E.Quality of Service （QoS）
F.Jitter management
您可能感興趣的試卷
你可能感興趣的試題
What can be determined about the HSRP relationship from the displayed debug output？（）
A.Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router172.16.11.112
B.The IP address 172.16.11.112 is the virtual HSRP router IP address
C.The nonpreempt feature is enabled on the 172.16.11.112 router
D.The IP address 172.16.11.111 is the virtual HSRP router IP address
E.Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router172.16.11.111
F.The preempt feature is not enabled on the 172.16.11.111 router
Examine the router output above. Which two items are correct？（）
A.If Ethernet 0/2 goesdown， the standby router will take over
B.The local IP address of Router A is 10.1.0.6
C.When Ethernet 0/3 of RouterA comes back up， the priority will become 105
D.Router A will assume the active state if its priority is the highest
E.The local IP address of Router A is 10.1.0.20
Refer to the exhibit. Based upon the debug output that is shown， which three statements aboutHSRP are true？（）
A.The router with IP address 172.16.11.112 is using default HSRP priority
B.The IP address 172.16.11.115 is the virtual HSRP IP address
C.The priority of the router with IP address 172.16.11.112 is preferred over the router with IPaddress 172.16.11.111
D.The router with IP address 172.16.11.111 haspreempt configured
E.The final active router is the router with IP address 172.16.11.111
F.The router with IP address 172.16.11.112 has nonpreempt configured
Refer to the exhibit. Which two problems are the most likely cause of the exhibited output？（）
A.VRRP misconfiguration
B.spanning tree issues
C.transport layer issues
D.physical layer issues
E.HSRP misconfiguration
Examine the router output above. Which two items are correct？（）
A.If Ethernet 0/2 goesdown， the standby router will take over
B.The local IP address of Router A is 10.1.0.6
C.When Ethernet 0/3 of RouterA comes back up， the priority will become 105
D.Router A will assume the active state if its priority is the highest
E.The local IP address of Router A is 10.1.0.20
最新試題
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
Which statement about PPPoA configuration is correct？（）
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）
Drag and drop each management protocol on the above to the correct category on the below.
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）