A.The IBGP routers must always be fully meshed
B.The IBGP routers can be in a different AS
C.The IBGP routers must be directly connected
D.The IBGP routers do not need to be directly connected
E.None of the other alternatives apply are true
您可能感興趣的試卷
你可能感興趣的試題
The network consists of two separate autonomous systems as shown below：
You need to configure Router R2 as a BGP route reflector and Router R1 as the client. Assumingthat Router R3 isn’t running BGP， which two of the commands below would you enter on R2 tosatisfy your goals？（）
A.neighbor 165.50.12.1 remote-as 65100
B.neighbor 165.50.12.2 remote-as 64000
C.neighbor 165.50.12.1 route-reflector-client
D.neighbor 165.50.12.2 route reflector-client
Refer to the exhibit. All routers are configured for BGP. EBGP routes received on router R2 showup in the BGP table on routers R1 and R3 but not in their IP routing tables. What would causethis？（）
A.EBGP multihop is not configured on routers R1 and R3
B.Routers R1 and R3 do not receive the same routes via an IGP
C.Synchronization in autonomous system 100 is turned is on
D.The BGP routers in autonomous system 100 are not logically fully-meshed
E.Synchronization in autonomous system 100 is turned is off
A.When traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose2 because of the higher MED value of SanJose2
B.The serial 0/0/1 interface on the ISP router has been configured with the set metric 50command
C.The output was generated by entering the show ip bgp command on the SanJose1 router
D.The output was generated by entering the show ip bgp command on the ISP router
E.The serial 0/0/1 interface on the ISP router has been configured with the set metric 75command
F.When traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose1 because of the lower MED value of SanJose1
Refer to the exhibit. Router RT3 discovers network 202.176.56.0 via BGP. Which one of thesestatements is true？（）
A.RT1 advertised network 202.176.50.0/24 with a metric of 782
B.RT3 is directly connected to RT1 using subnet 192.168.1.0
C.RT3 has an IGP metric of 782 to reach 192.168.1.1
D.RT3 has a BGP metric of 782 to reach 192.168.1.1
E.RT1 advertised network 202.176.50.0/24 with a metric of 1000
F.RT3 has an IGP metric of 1782 to reach 202.176.56.0/24
A.Memory requirements are higher for shared distribution tree than for source distributiontree.
B.Creates a tree from a central RP to all last-hoprouters.
C.Uses a rendezvous point.
D.An optimal path is created between each source router and each last-hoprouter.
E.Place（S，G）entry in each router’smulticast routing table.
F.Place（*，G）entry in a router’smulticast routing to table.
最新試題
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
Which three statements accurately describe IOS Firewall configurations？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Study the exhibit carefully. The Cisco IOS IPsec High Availability （IPsec HA） Enhancementsfeature provides an infrastructure for reliable and secure networks to provide transparent availability of the VPN gateways - that is， Cisco IOS Software-based routers. What are the twooptions that are used to provide High Availability IPsec？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）