多項選擇題Which two data link layers are supported by cisco ios software for IPv6?()

A.PPP
B.FDDI
C.Frame Relay PVC
D.NBMA
E.Frame Relay SVC


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題

Refer to the exhibit.Give this output for SwitchC, what should the network administrator’s next action be?()

A.Check the trunk encapsulation mode for SwitchC’s fa0/1 port.
B.Check the duplex mode for SwitchC’s fa0/1 port.
C.Check the duplex mode for SwitchA’s fa0/2 port.
D.Check the trunk encapsulation mode for SwitchA’s fa0/2 port.

2.單項選擇題Which PPP subprotocol negotiates authentication options?()

A.NCP
B.LCP
C.ISDN
D.DLCI
E.SLIP

3.多項選擇題

What can be determined from the line of show ip route output shown in the exhibit?()

A. The next routing update can be expected in 35 seconds. 
B. The IP address 10.10.10.6 is configured on S0/1. 
C. The IP address 10.10.10.8 is configured on S0/1.
D. This route is using the default administrative distance. 
E. The 10.10.10.8 network is two hops away from this router.

4.多項選擇題Which three statements accurately describe layer 2 Ethernet switches?()

A.Microsegmentation decreases the number of collisions on the network.
B.if a switch receives a frame for an unkown destination,it uses ARP to resolve the address.
C.Spanning Tree Protocol allows switches to automatically share vlan information.
D.In a properly functioning network with redundant switched paths,each switched aegment will contain one root bridge with all its ports in the forwarding state.All other switches in that broadcast domain will have only one root port.
E.Establishing vlans increases the number of broadcast domains.
F.Switches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.

5.單項選擇題

S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?()

A.Configure the no ip subnet-zero command on R1,R2,and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.

最新試題

請參見圖示。網絡技術人員試圖確定主機A 的正確IP 地址配置。以下哪一項是主機A 的有效配置?()

題型:?jiǎn)雾?xiàng)選擇題

請參見圖示。一臺路由器(其路由表如圖所示)收到發往192.168.1.4的數據包。路由器將如何處理該數據包?()

題型:?jiǎn)雾?xiàng)選擇題

請參見圖示。主機A 和B 無法互相通信。此問題的原因是什么?()

題型:?jiǎn)雾?xiàng)選擇題

請參見圖示。一臺主機正使用NAT 連接到Internet。下列哪三項IP 地址可實現此連接?()

題型:多項選擇題

要將數據包發送到遠程網絡,應使用哪種設備?()

題型:?jiǎn)雾?xiàng)選擇題

請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程?()

題型:?jiǎn)雾?xiàng)選擇題

請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2?()

題型:多項選擇題

請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€(gè)邏輯地址范圍?()

題型:?jiǎn)雾?xiàng)選擇題

路由器使用哪一項信息來確定源主機和目的主機之間的路徑?()

題型:?jiǎn)雾?xiàng)選擇題

傳輸層如何讓主機能同時針對不同應用程序維護多個通信流?()

題型:?jiǎn)雾?xiàng)選擇題