A.NCP
B.LCP
C.ISDN
D.DLCI
E.SLIP
您可能感興趣的試卷
你可能感興趣的試題
What can be determined from the line of show ip route output shown in the exhibit？（）
A. The next routing update can be expected in 35 seconds.
B. The IP address 10.10.10.6 is configured on S0/1.
C. The IP address 10.10.10.8 is configured on S0/1.
D. This route is using the default administrative distance.
E. The 10.10.10.8 network is two hops away from this router.
A.Microsegmentation decreases the number of collisions on the network.
B.if a switch receives a frame for an unkown destination,it uses ARP to resolve the address.
C.Spanning Tree Protocol allows switches to automatically share vlan information.
D.In a properly functioning network with redundant switched paths,each switched aegment will contain one root bridge with all its ports in the forwarding state.All other switches in that broadcast domain will have only one root port.
E.Establishing vlans increases the number of broadcast domains.
F.Switches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally， static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes？（）
A.Configure the no ip subnet-zero command on R1,R2,and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
Which destination addresses will be used by Host A to send data to Host C？（）
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router’s E0 interface
F. the MAC address of the router’s E0 interface
An administrator is unsuccessful in adding VLAN 50 to a switch. While troubleshooting the problem，the administrator views the output of the show vtp status command， which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database？（）
A. Switch（config-if）# switchport access vlan 50
B. Switch（vlan）# vtp server
C. Switch（config）# config-revision 20
D. Switch（config）# vlan 50 name Tech
E. Switch（vlan）# vlan 50
F. Switch（vlan）# switchport trunk vlan 50
最新試題
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程？（）
請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口？（）
何時必須使用clock rate 命令配置路由器串行接口？（）
在配置路由器時，網絡技術人員想要命名路由器。輸入hostname 命令后，技術人員會看到下列哪一項提示？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€邏輯地址范圍？（）
請參見圖示。對于從主機A 向Web 服務器發出的網頁請求，正確的目的套接字?jǐn)?shù)字是什么？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲写嬖诙嗌賯€廣播域？（）
傳輸層如何讓主機能同時針對不同應用程序維護多個通信流？（）
在Cisco IOS 設備中，啟動配置文件存儲于何處？（）
請參見圖示。已啟用路由器的NAT 功能供PC 訪問Internet?？梢詾槁酚善鹘涌赟0/0/0分配下列哪一個IP 地址？（）