A.rogue detector
B.rogue containment
C.RLDP
D.RIDP
您可能感興趣的試卷
你可能感興趣的試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The
phone rings but， when you answer， the call is dropped.
What may have caused this problem？（）
A.Publicly Secure Packet forwarding is enabled.
B.The minimum data rate is not set to 11 Mbps.
C.An address resolution protocol is enabled.
D.The access point is set to the least congested channel.
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor， 4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the network and isbeing monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of them are beingtracked on the Cisco WCS.
What can be done to correct the problem？（）
A.Add a new location appliance.
B.Add a new Cisco WCS server dedicated to the location appliance.
C.Add 4 GB of RAM to the Cisco WCS.
D.Add a 120 GB hard drive to the Cisco WCS.
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be a roaming bandwidth issue. In order to verify what kindof issue it is， you decide to increase the bandwidth reserved for roaming on the WLAN controllerto the maximum.
What level do you set the bandwidth to？（）
A.25 percent
B.15 percent
C.5 percent
D.35 percent
Using the WLSE， you are trying to push out a configuration job to a standalone access point， butthe job does not start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.pop-up blocker enabled in the browser
D.unsupported version of IOS firmware in the access point
A.50
B.128
C.512
D.1024
最新試題
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）