A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it，which continue to pass traffic.
What has causedthis problem？（）
A.H-REAP AP1 has reached its client limit.
B.H-REAP AP2 has reached its client limit.
C.H-REAP AP2 lost its connection to the controller.
D.H-REAP AP1 lost its connection to the controller.
您可能感興趣的試卷
你可能感興趣的試題
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied.
What is wrong？（）
A.Polling values can be changed only in the maintenance window.
B.Polling values can be changed only on the location server.
C.Your login does not have the correct permissions.
D.You must wait for the location server to become available.
On a Cisco 1000 Series controller-based access point， the alarm LED is flashing red， but the otherLEDs are off.
What is this access point indicating？（）
A.Its IP address already exists.
B.It is operating normally.
C.It requires a code upgrade.
D.It has lost contact with the controller.
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.
Which situation would result in thistype ofproblem？（）
A.Posture validation has not been enabled
B.The AAA server is set to accept both MS-CHAP v2 and GTC for PEAP authentication
C.Clients and server are not using certificates
D.Clients have been set to validate the server identity
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter， the status LED and activity LED arealternating on and off.
What does this indicate？（）
A.The client card is not associated to the network.
B.The client card has awakened from power-save mode.
C.The driver has been installed incorrectly.
D.The client card has failed.
You have very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops. Youwant to increase the bandwidth available for the laptops by decreasing the bandwidth reserved forthe Cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidth you can select onthe WLAN controller？（）
A.55 percent
B.75 percent
C.40 percent
D.25 percent
最新試題
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）