You are installing a Cisco 4402 Series Wireless LAN Controller.
Which type of interface should you use on the controller’s distribution port？（）
A.1000BASE-SX SFP
B.10/100/1000 Mbps RJ45
C.10/100 Mbps RJ45
D.10000BASE-SX
您可能感興趣的試卷
你可能感興趣的試題
By default， on the WLAN controller for a voice application using Cisco 7921 wireless IP phones.
What is the percentage of RF bandwidth that can be dedicated to the phones？（）
A.75 percent
B.85 percent
C.56 percent
D.55 percent
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware. Before you press and hold the MODEbutton.
You should verify that the file name is which of the following？（）
A. c1130-k9w7-tar.boot
B. c1130-k9w7-tar.123-7.JA1.tar
C. c1130-k9w7-tar.default
D. c1130-k9w7-tar.recove
A.Problem Management
B.Configuration Management
C.Incident Management
D.Change Management
A.15
B.10
C.1
D.5
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’sperspective？（）
A.Received Mobile Anchor Export message
B.Transmit Plumbing duplex mobility tunnel message
C.Received Plumbing duplex mobility tunnel message
D.Transmit Mobile Anchor Export message
最新試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）