You review the failed attempts logs on an aaa server and find： "unknown network access server error."
Which failure could produce this error？（）
A.failure of the wireless client and aaa server handshake
B.supplicant authentication failure
C.aaa client and aaa server handshake
D.wrong password used by the supplicant
您可能感興趣的試卷
你可能感興趣的試題
You are troubleshooting a problem with a cisco 7920 wireless ip phone that is causing the phone to drop calls. the problem appears to be roaming bandwidth issuE. in order to verify what kind of issue it is， you decide to increase the bandwidth reserve for roaming on the wlan controller to maximum.
What level do you set the bandwidth to？（）
A.5 percent
B.15 percent
C.25 percent
D.35 percent
A.back up the database， stop the wcs， upgrade the wcs， restore the database， start the wcs
B.stop the wcs， back up the database， upgrade the wcs， restore the database， start the wcs
C.back up the database， stop the wcs， upgrade the wcs， start the wcs， restore the database
D.stop the wcs， back up the database， upgrade the wcs， start the wcs， restore the database
When optimizing a standalone point-to-multipoint bridge installation with eight non-root bridges.
Which of the following rts threshold and cwmin settings would be correct for the non-root bridges？（）
A.rts threshold=4000，cwmin=3
B.rts threshold=1，cwmin=4
C.rts threshold=4000，cwmin=5
D.rts threshold=1，cwmin=5
A.debug dhcp enable
B.debug dhcp status enable
C.debug dhcp packet enable
D.enable debug dhcp packet
You are troubleshooting a one-way call problem with a cisco 7920 wireless ip phone on a standalone wlan.
What may cause this problem？（）
A.the minimum data rate is not set to 11 mbps.
B.an address resolution protocol has been disabled
C.publicly secure packet forwarding is enabled
D.the access point is set to the least congested channel.
最新試題
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）