You are using standalone cisco aironet 1400 series wireless bridges for a nine-mile point-to-point wireless link between two buildings.
Which distance setting should you use for the bridge configured as the root？（）
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
您可能感興趣的試卷
你可能感興趣的試題
When configuring a cisco 3845 integrated services router to support 802.11b and g clients.
Which of the following commands would be correct？（）
A.router（config-if）# speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
B.router（config-if）# speed 1.0 2.0 5.5 6.0 9.0 basic-11.0 12.0 basic-18.0 24.0 36.0 48.0 54.0
C.router（config-if）# speed basic-1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
D.router（config-if）# speed 1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
A.enable concatenation on the non-root bridge only
B.enable concatenation on the root bridge only
C.enable concatenation on both the root bridge and non-root bridge
D.enable concatenation on the root bridge and set it as desirable on the non-root bridge
E.set concatenation as desirable on the root bridge and enable it on the non-root bridge
Eap-fast provides a secure tunnel during phase one to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel？（）
A.x.509 certificate
B.generic token card
C.pre shared key
D.protected access credential
Your customer has deployed a cisco wireless location appliance within its warehouse
environment. however，employees there have been experiencing problems when tracking objects using active rfid tags. the rfid beacon rate is 10 seconds and you have discovered an issue with the rfid timeout value.
Where and how should the rfid value be changed？（）
A.on the cisco wcs， to 95 seconds
B.on the wireless controller， to 45 seconds
C.on the wireless controller， to 95 seconds
D.on the cisco wcs， to 45 seconds
You are installing a cisco aironet 1000 series controller-based access point. when you boot it， all the leds on the access point blink together.
What does this indicate about the access point？（）
A.duplicate ip address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
最新試題
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）