A. When a router receives a failure response, it stops querying authentication methods.
B. When a router receives an error response, it stops querying authentication methods.
C. If the router receives a failure response from an authentication method, it queries the next method.
D. The router does not differentiate between failure and error responses; the authentication process is always interrupted.
E. If it receives no response from the authentication method, a router will determine the error condition on its own; the router also has the option to proceed to the next method in a list if configured accordingly.
您可能感興趣的試卷
你可能感興趣的試題
A. It is achieved by using more than one HSRP group.
B. It is done in regards to either round robin or weight basis.
C. It is used to offload the active router in a certain HSRP group.
D. Single group HSRP is used to achieve more efficient link utilization.
E. The return traffic is influenced by HSRP load sharing configuration.
A. RIP does not support routing contexts
B. routing contexts are implemented in a single routing process
C. routing contexts are implemented using multiple routing processes
D. routing contexts are implemented as several instances of a single routing process
E. routing contexts are implemented as a single instance of several routing processes
A. start LDP
B. enable CEF switching
C. configure the MPLS ID
D. disable IP TTL propagation
E. configure conditional label advertising
F. enable label switching on frame mode interfaces
A. to make CEF tables smaller
B. to enable label switching on the frame mode interface
C. to restrict MPLS availability to predefined time periods
D. to restrict label switching to a limited number of networks
E. to restrict end users from seeing the routers in the MPLS network
A. If using IS-IS as the PE-CE routing protocol, no redistribution is required.
B. If using static routes between the CE and PE routers, no redistribution of other VPN routes is required.
C. If the PE-CE protocol is not BGP, redistribution of other VPN routes from MP-BGP is required.
D. If RIP is the routing protocol that is used between the PE-CE routers, no redistribution is required, but any other protocol will require redistribution.
E. If using OSPF or EIGRP as the PE-CE routing protocol, redistribution is not required, but any other protocol or static route will require redistribution.
最新試題
Which Cisco IOS command is used to troubleshoot a problem in which a BGP session stays in the active state?（）
Refer to the exhibit. For the given configuration, on packets leaving the router on interface FastEthernet0/0 that matches the high traffic class, what will the MPLS experimental bit be set to?（）
What is the purpose of using VPN hardware acceleration equipment?（）
Which configuration will enable OSPF for IPv6 on FastEthernet 0/0/0?（）
As an experienced network engineer, you are asked to troubleshoot a CIS network outage. During the troubleshooting process, you notice that one of your colleagues connects additional devices to the network with the use of his own switch. With the purpose of improving speed, the switch is attached to both network ports in an office, which leads to bridge loop.Enabling which of the following feature will be able to prevent this problem from happening again?（）
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）
With a VPN Accelerator Module 2+ (VAM2+) installed in a Cisco 7200 series router, what will be the resulting action when entering the command no crypto engine accelerator slot number?（）
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）
You are trying to initiate an SSH connection to a remote router and are getting rejected with an error code of 0. Which of these might be the cause of the error?（）
Refer to the exhibit. Which two of these statements are correct? (Choose two.)（）