On a cisco aironet 802.11 a/b/g wireless lan client adapter， the status led and activity led are alternating on and off.
What does this indicate？（）
A.the client card is not associated to the network.
B.the client card has awakened from power-save mode.
C.the driver has been installed incorrectly.
D.the client card has failed.
您可能感興趣的試卷
你可能感興趣的試題
You have very few cisco 7920 wireless ip phones on your network， but lots of wireless laptops. You want to increase the bandwidth available for the laptops by decreasing the bandwidth
reserved for the cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidth you can select on the wlan controller？（）
A.55 percent
B.75 percent
C.40 percent
D.25 percent
A.windows 2000 sp4
B.windows server 2003
C.solaris 10
D.vista
E.windows xp pro
Your customer has deployed a cisco wireless location appliance within its warehouse
environment. however， employees there have been experiencing problems when tracking objects using active rfid tags. you use an access point scan to determine if the location appliance has been deployed correctly.
Making which change to warehouse deployment location services will most likely correct the problem？（）
A.ensure channels are deployed such that they do not overlap
B.allow for the automatic containment of rogue access points
C.ensure each area is covered by a minimum of three access points
D.ensure a minimum rssi value of -50
A.4
B.32
C.8
D.16
A cisco 4404 wlan controller is being connected to a cisco 6500 catalyst series switch.
How would you interconnect and configure lag for connectivity and ensure redundancy？（）
A.all four ports from the cisco wlc terminated to the same catalyst gigabit module and channel group.
B.ports 1 and 2 from cisco wlc to catalyst gigabit module slot 1 channel group 10 and cisco wlc ports 3 and 4 to catalyst gigabit module slot 2 channel group 10.
C.all four ports from the cisco wlc terminated to the same catalyst gigabit module using two channel groups.
D.ports 1 and 2 from cisco wlc to catalyst gigabit module slot 1 channel group 20 and cisco wlc ports 3 and 4 to catalyst gigabit module slot 2 channel group 40.
最新試題
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）