The following output occurs on Router R1. Which of the following cannot be determine d from this output?()
R1# show ip route 180.1.1.0 255.255.255.240
Routing entry for 180.1.1.0/28
Known via "bgp 2", distance 20, metric 0
Tag 3, type external
Last update from 192.168.1.2 00:10:27 ago
Routing Descriptor Blocks:
* 192.168.1.2, from 19 2.168.1.2, 00:10:27 ago
Route metric is 0, traffic share count is 1
AS Hops 2
Route tag 3
A. The type of BGP peer (iBGP or eBGP) that advertised this route to R1
B. R1's ASN
C. The next - hop router's ASN
D. The AS_Path length
您可能感興趣的試卷
你可能感興趣的試題
A. It lists a set of path attributes, along with a list of prefixes that use those PAs
B. It lists a prefix/length, plus the PA settings for that prefix
C. It lists withdrawn routes, but never in the same Update message as newly advertised routes
D. A single Update message lists at most a single prefix/lengtH
The following output was taken from the show ip bgp command on Router R2. In this case, which of the following commands are most likely to already be configured on R2?()
BGP router identifier 11.11.11.11, local AS number 11
...
Neighbor V AS Ms gRcvd MsgSent TblVer InQ OutQ Up/Down
State/PfxRcd
1.1.1.1 4 1 87 87 0 0 0 00:00:06 Idle
(Admin)
2.2.2.2 4 3 173 183 41 0 0 00:58:47
A. router bgp 11
B. neighbor 1.1.1.1 remote- as 11
C. neighbor 2.2.2.2 prefix - limit 1
D. neighbor 1.1.1.1 shutdown
The following output, taken from a show ip bgp command on Router R1, lists two neighbors. In what BGP neighbor state is neighbor 1.1.1.1?()
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down
State/PfxRcd
1.1.1.1 4 1 60 61 26 0 0 00:45:01
0
2.2.2.2 4 3 153 159 26 0 0 00:38:13
1
A. Idle
B. Opensent
C. Active
D. Established
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively.
Which of the following commands would not be part of a working eBGP confi guration on Router R1?()
A. router bgp 1
B. neighbor 2.2.2.2 remote- as 2
C. neighbor 2.2.2.2 update - source loopback1
D. neighbor 2.2.2.2 multihop 2
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link.
Which of the following commands would be needed on R1 to configure eBGP?()
A. router bgp 2
B. router bgp 1
C. neighbor 10.1 .1.2 remote - as 2
D. neighbor 10.1.1.2 Update - source 10.1.1.1
E. neighbor 10.1.1.2 Update- source S0/0
最新試題
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 lists the following output from a show command. Which of the following is true about R1?()R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?()Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Which of the following are true of both OSPFv2 and OSPFv3?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output?()B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18