Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface.
What command would make this router not use a DR and require static OSPF neighbor definition?（）
A. ip ospf network broadcast
B. ip ospf netw ork non - broadcast
C. ip ospf network point - to - multipoint
D. ip ospf network point - to - multipoint non - broadcast
您可能感興趣的試卷
你可能感興趣的試題
Several links have been broken so th at for the next day or two, what was formerly a contiguous area 0 has been broken into two parts. However, both parts of area 0 have working links into area 1 using routers with RID 1.1.1.1 and 2.2.2.2.
Which answers list the command on the router with RID 1.1.1.1 to create a virtual link to help solve this temporary problem?（）
A. area 0 virtual - link 2.2.2.2
B. area 1 virtual - link 2.2.2.2
C. area 0 source - rid 1.1.1.1 dest - rid 2.2.2.2
D. virtual - link transit - area 1 RID 2.2.2.2
Which of the following answers can be verified as true based on the following command output from Router R1?（）
R1#show ip ospf virtual - links
Virtual Link OSPF_VL0 to router 4.4.4.4 is up
Run as demand circuit
DoNotAge LSA alloweD.
Transit area 1, via interface FastEthernet0/1, Cost of using 3
A. R1 is configured with an area 0 virtual - link 4.4.4.4 cost 3 command.
B. The ping 4.4.4.4 command on R1 must currently be successful.
C. R1's Fa0/0 OSPF cost is 3.
D. 4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.
A. Stub
B. Totally stubby
C. NSSA
D. Totally NSSA
A. Routers cannot redistribute external routes into the area.
B. Routers should have zero Type 3 LSAs in their LSDBs.
C. Routers should have zero Type 5 LSAs in their LSDBs.
D. Routers should learn default routes from the ABRs attached to the area.
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command.
Which of the following is true about the effects of this configuration command?（）
A. R1 will always create and flood a default route into the OSPF domain.
B. R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.
C. R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.
D. R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
最新試題
Which of the following answers lists a multicast IPv6 address?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18