A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC.
Which of the following is true about OSPF in this design?（）
A. The central site router has 100 fully adjacent neighborships with the 100 branches
B. The central site router has neighborships with all branch routers, but fully adjacent neighbors with only two branches
C. The central site router has a neighborship with the Frame Relay switcH
D. None of the other answers is correct
您可能感興趣的試卷
你可能感興趣的試題
A. The interface used to connect to that neighbor being passive in the OSPF process
B. Duplicate OSPF router IDs
C. Mismatched dead timers
D. IP addr esses of 10.1.1.1/24 and 10.2.2.2/24
E. Mismatched OSPF process IDs
Routers R1 and R2, OSPF neighbors in area 0 over their Fa0/0 interfaces (respectively), currently both successfully use OSPF MD5 authentication. The OSPF configuration includes the area 0 authentication command under the router ospf 1 command.
Which of the following commands must have been configur ed on R1's Fa0/0 interface?（）
A. ip ospf authentication null
B. ip ospf authentication message - digest
C. ip ospf authentication -key whatever- it - is
D. ip ospf message - digest - key 1 md5 whatever - it - is
E. ip ospf md5 1 key whatever - it - is
Routers R1 and R2 are OSPF neighbors using their Fa0/0 interfaces, respectively, using default settings for all timers. An engineer ad ds the ip ospf hello - interval 6 command to R1's Fa0/0 configuration.
Which of the following is true regarding the results from this change?（）
A. The show ip ospf neighbor command on R1 lists the revised Hello timer
B. The show ip ospf interfac e brief command on R1 lists the revised Hello timer
C. The R1 - R2 neighborship fails due to Hello timer mismatcH
D. The show ip ospf interface command on R1 lists the revised Hello timer
Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers.
Which of the following is true on R1?（）
A. The show ip ospf neighbors command lists two neighbors off Fa0/0.
B. The show ip ospf neighbors command lists four neighbors off Fa0/0.
C. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.
D. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
A. show ip ospf database
B. show ip ospf interface brief
C. show ip protocols
D. show ip route ospf
E. show ip ospf neighbors
最新試題
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）