A.Address Resolution Protocol （ARP）
B.PDU header rewrite
C.NetFlow switching
D.hello packet exchange
您可能感興趣的試卷
你可能感興趣的試題
A.Switch（config-if）#spanning-tree guard root
B.Switch（config-if）#spanning-tree portfast
C.Switch（config-if）#switchport mode trunk
D.Switch（config-if）#switchport mode access
A port in a redundant topology is currently in the blocking state and is not receiving BPDUs. To ensure that this port does not erroneously transition to the forwarding state，
which command should be configured to satisfy the requirement？（）
A.Switch（config）#spanning-tree loopguard default
B.Switch（config-if）#spanning-tree bdpufilter
C.Switch（config）#udld aggressive
D.Switch（config-if）#spanning-tree bpduguard
A.spanning-tree guard root
B.spanning-tree portfast bpduguard default
C.spanning-tree bpduguard enable
D.spanning-tree bpdufilter enable
E.spanning-tree portfast bpdufilter default
A.a native VLAN mismatch on either side of an 802.1Q link
B.BPDU filter configured on a link to another switch
C.Spanning Tree Protocol enabled on both Layer 2 and multilayer switches
D.PortFast enabled on all access and trunk ports
A.Configuration changes made on the port-channel interface apply to all physical ports assigned to the portchannel interface.
B.Configuration changes made on a physical port that is a member of a port-channel interface apply to the port-channel interface.
C.Configuration changes are not permitted with Port Aggregation Protocol； instead， the standardized Link Aggregation Control Protocol should be used if configuration changes are required.
D.The physical port must first be disassociated from the port-channel interface before any configuration changes can be made.
最新試題
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）