A.detailed list of personnel assigned to each task within the plan
B.a Layer 2 spanning tree design topology
C.rollback guidelines
D.placing all unused access ports in VLAN 1 to proactively manage port security
E.enabling SNMP access to Cisco Discovery Protocol data for logging and forensic analysis
您可能感興趣的試卷
你可能感興趣的試題
A.detailed VLAN information
B.an incident response plan
C.results of testing the new network configuration
D.an existing hierarchical network topology
E.a security policy for your organization
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.a list of applications currently in use in the network
B.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
C.detailed security device specifications
D.results from pilot network testing
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.detailed security device specifications
C.results from pilot network testing
D.results from a network audit
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.a list of the customer requirements
C.detailed security device specifications
D.results from pilot network testing
Cat6500（config）# router ospf 1
Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0
Cat6500（config-router）# nsf Cat6500（config-router）#end
Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series
Switch with redundant supervisor engines.
The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational.
What is the most likely reason？ （）
A.CEF was not properly configured.
B.OSPF was not properly configured for graceful restart.
C.Stateful switchover was not correctly configured.
D.NSF for OSPF is only supported in area 0.
最新試題
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Which router redundancy protocol cannot be configured for interface tracking？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）