Refer to the exhibit. A new TAC engineer comes to you for advice. The engineer wants to configure RIPv2 - OSPF two - way redistribution while avoiding routing loops. Which two additio ns to the router B1 configuration should the engineer make?（）
A. access - list 40 deny 172.16.1.0 0.0.0.255 access - list 40 permit any router rip redistribute ospf 100 metric 5 distribute- list 40 out ospf 100
B. ip prefix - list rip_routes permit 172. 16.1.16/25 ge 26 le 28 route - map redis - ospf deny 10 match ip address prefix- list rip_routes router rip redistribute ospf 10 route - map redis - ospf subnets
C. ip prefix - list rip - to - ospf permit 10.1.1.8/25 ge 26 le 28 route - map redis - rip deny 20 match i p address prefix - list rip - to - ospf router ospf 100 redistribute rip route - map redis - rip subnets
D. access - list 15 deny 10.1.1.0 0.0.0.63 access - list 15 permit any route - map redis - rip deny 10 match ip address 15 route - map redis - rip permit 20 router os pf 100 redistribute rip route - map redis - rip subnets
您可能感興趣的試卷
你可能感興趣的試題
A. retransmit - interval
B. de ad - interval
C. stub area
D. virtual link
E. NSSA area
A. Routes learned using any IP routing protocol can only be redistributed into non IP routing protocols.
B. OSPF can import routes learned using EIGRP, RIP, and IS - IS.
C. OSPF routes cannot be exported into EIGRP, RIP, an d IS - IS.
D. At the interdomain level, OSPF cannot import routes learned using BGP.
E. OSPF routes can be exported into BGP.
Refer to the exhibit. Currently the two eBGP links between AS100 and AS200 have an average inbound load of 65% and 20% respectively. After further investigation, traffic to 10.10.1.16/28 accounts for 45%, and t raffic to 10.10.1.32/28 and to 10.10.1.48/28 each account for 20% of the inbound load. The BGP attributes are currently set at their default values in both autonomous systems. If you want to influence how AS200 sends traffic to AS100, which eBGP configu rations would you configure in AS100 to influence AS200 to use the eBGP links more evenly?（）
A. neighbor 192.168.30.2 route - map as_50 out
B. neighbor 192.168.20.2 route - map as_50 out
C. route - map as_50 permit 10 match ip address 50 set metric 150 a ccess - list 50 permit 10.10.1.16 0.0.0.240
D. route - map as_50 permit 10 match ip address 50 set metric 150 access - list 50 permit 10.10.1.32 0.0.0.240
Refer to the exhibit. A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the tunnel is not coming up. W hat did the TAC engineer configure incorrectly?（）
A. The crypto isakmp configuration is not correct.
B. The crypto map configuration is not correct.
C. The interface tunnel configuration is not correct.
D. The network configuration is not correct; netw ork 172.16.1.0 is missing.
Refer to the exhibit. Examine the partial configuration and the routing table excerpt. Which routes would be redistributed into OSPF area 1?（）
A. 10.10.10.16/28 only
B. 10.10.10.16/28 and 10.10.10.64/26
C. 10.10.10.16/28, 10.10.10.64/26, and 172.16.10.0/24
D. 10.10.10.64/26 only
最新試題
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following answers lists a multicast IPv6 address?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i