Refer to the exhibit. On the basis of the configuration provided, how are the Hello packets sent by R2 handled by R5 in OSPF area 5?()
A. The Hello packets will be exchanged and adjacency will be established between routers R2 and R5.
B. The Hello packets will be exchanged but the routers R2 and R5 will become neighbors only.
C. The Hello packets will be dropped and no adjacency will be established between routers R2 and R5.
D. The Hello packets will be dropped but the routers R 2 and R5 will become neighbors.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? ()
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not m atch.
A. Verify that the EIGRP hello and hold timers match exactly.
B. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.
C. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.
D. Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.
Refer to the exhibit. Routing updates for the 192.168.1.0 network are being received from all three neighbors. Which statement is correct regarding the result of the con figuration shown? ()
A. The router will prefer the next hop of 172.16.1.1 for packets destined for the 192.168.1.0 network.
B. The router will prefer the next hop of 172.26.1.1 for packets destined for the 192.168.1.0 network.
C. The router will adve rtise the 192.168.1.0 network only to 172.30.1.1.
D. The router will advertise the 192.168.1.0 network only to 172.26.1.1.
E. The router will prefer the next hop of 172.26.1.1 for packets except those destined for the 192.168.1.0 network.
Refer to the e xhibit. It is desired to set up a BGP neighbor relationship between routers R1 and R4. BGP packets between them could travel through R2 or R3. What is the simplest configuration that will allow for failover?()
A. Configure BGP n eighbor relationships between all interfaces on R1 and R4.
B. Install a direct connection between R1 and R4.
C. Configure loopback interfaces on R1 and R4 to provide the update source address for BGP packets.
D. Configure only one neighbor relationship between R1's 192.168.1.2 interface and R4's 172.16.10.2 interface.
A. In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3 areas.
B. In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3 areas.
C. In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to OSPFv3 areas.
D. In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to OSPFv3 areas.
最新試題
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Look at the following configuration below and select the statements that are true.()RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?()
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?()interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?()
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?()ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable