Refer to the exhibit. Based on the debug standby output in the exhibit， which HSRP statement is true？ （）
A. DSW111 is the active router because it is the only HRSP-enabled router on that segment.
B. DSW111 is the active router because the standby timer has been incorrectly configured.
C. DSW111 is the active router because it has a lower priority on that VLAN.
D. DSW111 is the active router because it has a lower IP address than the tying priority router on that VLAN.
E. DSW111 is the active router and is advertising the virtual IP address 10.10.10.111 on VLAN 11.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Based on the debug standby output in the exhibit，
which HSRP statement is true？（）
A. DSW111 is the active router because it is the only HRSP-enabled router on that segment.
B. DSW111 is the active router because the standby timer has been incorrectly configured.
C. DSW111 is the active router because it has a lower priority on that VLAN.
D. DSW111 is the active router because it has a lower IP address than the tying priority router on that VLAN.
E. DSW111 is the active router and is advertising the virtual IP address 10.10.10.111 on VLAN 11.
Refer to the exhibit. Assume that Host A can ping the corporate headquarters and that HSRP is configured on DSw1， which is then reloaded. Assume that DSw2 is then configured and reloaded. On the basis of this information，
what conclusion can be drawn？ （）
A. DSw1 will be the active router because it has the lower priority configured.
B. DSw1 will be the standby router because it has the lower IP address.
C. DSw2 will be the active router because it booted last.
D. DSw1 will be the active router because it booted first.
E. DSw2 will be the active router because it has the higher priority that is configured.
F. DSw2 will be the standby router because it has the higher IP address.
A. Spanning Tree Protocol （STP）
B. Delay reduction
C. Hot Standby Routing Protocol （HSRP）
D. Dynamic routing protocols
E. Quality of Service （QoS）
F. Jitter management
What can be determined about the HSRP relationship from the displayed debug output？ （）
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
Examine the router output above.
Which two items are correct？ （）
A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown， the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up， the priority will become 105.
E. Router A will assume the active state if its priority is the highest.
最新試題
Which statement is correct about the use of the virtual interface on a WLC ？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
What two things will occur when an edge port receives a BPDU？（）
Which two statements are true when the extended system ID feature is enabled？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）