Intermediate system to intermediate system (IS - IS), is a protocol used by network devices (routers) to determine the best way to forward datagrams through a packet - switched network, a process called routing. Which three attributes are of the IS - IS routing protocol? ()
A. supports VLSM
B. link - state routing protocol
C. operati on is similar to BGP
D. supports two routing levels within an autonomous system
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Which two statements are true?()
A. DHCPDISCOVER packets will reach the DHCP server.
B. The router will not forward DHCPDIS COVER packets because it has not been configured to do so.
C. This configuration is applied to interface Fa0/1.
D. DHCPDISCOVER packets will not reach the DHCP server because DHCPDISCOVER packets are broadcasts.
E. DHCPDISCOVER packets will not reach the DHCP server because ports 67 and 68 have not been explicitly allowed by the ip forward - protocol command.
F. This configuration is applied to interface Fa0/0.
A. when all equipment is manufactured by Cisco
B. when there are multiple paths to destination networks
C. because having multiple routing protocols confuses hackers
D. when migrating from an older Interior Gateway Protocol (IGP) to a new IGP
E. when using UNIX host - based routers
F. when smaller broadcast domains are desired
A. The multicast sources must register with the RP to form the multicast distribution tree.
B. An RP is required only in networks running Protocol Independent Multicast dense mode (PIM DM).
C. The mu lticast receivers must register with the RP to form the multicast distribution tree.
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM).
E. An RP is required only in networks running Protocol Independent Mu lticast sparse - dense mode (PIM - SDM).
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP.
Refer to the exhibit. Based upon the information in the exhibit, which statement is true?()
A. DHCP requests from the host will be rebroadcasted to R2.
B. To complete t his configuration, the R1 fa0/0 interface must be configured with the ip helper - addresses command.
C. To complete this configuration, the R2 fa0/0 interface must be configured with the ip helper -addresses command.
D. R1 will forward all DHCP requests t o both 192.168.100.1 and 192.168.200.1 as unicast messages.
E. R1 will forward DHCP requests to 192.168.100.1. If there is no response, R1 will then forward the requests to 192.168.200.1.
Refer to the exhibit. Which configuration would correctly enable Host A to acquire an IP address from the DHCP server that is located at 10.1.2.10/24? ()
A.ASw1(config)# interface range FastEthernet 0/1 - 24 ASw1(config - if - range)# ip forward - protocol udp 67 ASw1(config - if - range)# ip forward - protocol udp 68
B.ASw1(config)# interface range FastEthernet 0/1 - 24 ASw1(config - if - range)# ip helper - address 10.1.2.10
C.RTA(config)# interface fastethernet0/0 RTA(config -if)# ip forward- protocol udp 67 RTA(config - if)# ip forwar d- protocol udp 68
D.RTA(config)# interface fastethernet0/1 RTA(config -if)# ip forward- protocol udp 67 RTA(config -if)# ip forward- protocol udp 68
E.RTA(config)# interface fastethernet0/0 RTA(config - if)# ip helper - address 10.1.2.10
F.RTA(config)# in terface fastethernet0/1 RTA(config - if)# ip helper - address 10.1.2.10
最新試題
Which of the following are true of both OSPFv2 and OSPFv3?()
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?()
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
Router R1 lists the following output from a show command. Which of the following is true about R1?()R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?()
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?()
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?()
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64