Refer to the exhibit. HSRP has been configured and Link A is the primary route to router R4. When Link A fails， router R2 （Link B） becomes the active router.
Which router will assume the active role when Link A becomes operational again？" （）
A. The primary router R1 will reassume the active role when it comes back online.
B. The standby router R2 will remain active and will forward the active role to router R1 only in the event of its own failure.
C. The standby router R2 will remain active and will forward the active role to router R1 only in the event of Link B failure.
D. The third member of the HSRP group， router R3， will take over the active role only in event of router R2 failure.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. The Gateway Load Balancing Protocol has been configured on routers R1 and R2， and hosts A and B have been configured as shown.
Which statement can be derived from the exhibit？（）
A. The hostA default gateway has been configured as 10.88.1.10/24.
B. The GLBP weighted load balancing mode has been configured.
C. The GLBP round-robin， load-balancing mode has been configured.
D. The GLBP host-dependent， load-balancing mode has been configured.
E. The hostA default gateway has been configured as 10.88.1.1/24.
F. The hostA default gateway has been configured as 10.88.1.4/24.
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails？（）
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
Routers can send hello messages in three HSRP states.
Which ones are they？（）
A. Standby
B. Learn
C. Listen
D. Speak
E. Active
Router R1 is configured for HSRP.
Which of the following are valid HSRP states on R1？ （）
A. Init
B. Idle
C. Active
D. Standby
E. Established
F. Backup
You have configured router R1 with HSRP， using the standard defaults.
Which three statements are true of a default HSRP configuration？（）
A. The Standby hello time is 2 seconds.
B. Two HSRP groups are configured.
C. The Standby track interface priority is 10.
D. The Standby hold time is 10 seconds
E. The Standby priority is 100.
F. The Standby delay is 3 seconds.
最新試題
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Which three statements about STP timers are true？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）