Based on the show ip bgp summary output, which two statements are true?（）
A. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.
B. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.
C. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.
D. The BGP session to the 10.3.3.3 neighbor is established.
E. The BGP session to the 10.2.2.2 neighbor is established.
F. The BGP session to the 10.1.1.1 neighbor is established.
您可能感興趣的試卷
你可能感興趣的試題
A. An internal routing protocol can be used to reach an EBGP neighbor.
B. The next hop does not change when BGP updates are exchanged between EBGP neighbors.
C. EBGP requires a full mesh.
D. A static route can be used to form an adjacency between neighbors.
When an IPv6 enabled host boots, it sends a router solicitation (RS) message. An IPv6 router responds with a router advertisement (RA).
Which two items are c ontained in the RA?（）
A. any route advertisements it has received
B. prefixes for the link
C. keepalive timers
D. IPv6 address for the host
E. request for the local host IP address
F. lifetime of the prefix
A. They must be fully meshed
B. They can be in a different AS
C . They do not need to be directly connected
D. They must be directly connected
Refer to the exhibit diagram and config uration. RTB is summarizing its networks from AS 64100 with the aggregate - address command. However, the show ip route command on RTA reveals the RTB individual networks as well as its summary route.
Which option would ensure that only the summary route would appear in the routing table of RTA?（）
A. Add a static route with a prefix of 192.168.24.0 255.255.252.0 pointing to the null0 interface.
B. Create a route map permitting only the summary address.
C. Delete the four network statements and leave onl y the aggregate - address statement in the BGP configuration.
D. Add the keyword summary - only to the aggregate - address command.
Observe the diagram. RTC is the hub router and RTA and RTB are the spokes. There are no virtual circuits between the spoke locations. What is needed to successfully route traffic to the 11.11.11.0/24 network from RTA? （）
A. The neighbor 10.10.10.1 next - hop - self com mand on RTA
B. Nothing is required. This is the default behavior on this topology
C. The neighbor 10.10.10.1 next - hop - self command on RTB
D. The neighbor 10.10.10.1 next - hop - self command on RTC
最新試題
Which of the following features work the same in both RIP- 2 and RIPng?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）