A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values.
Which statement is true about how BGP would select the best path?（）
A. To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50
B. Th e router will prefer the shortest autonomous system path
C. If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MED
D. The router will prefer the route with the lower MED
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Which two statement s are correct?（）
A. All the routes were redistributed into BGP from an IGP
B. All the routes were originated by BGP with the network command
C. All six routes will be installed in the routing table
D. Four routes will be installed in the routing ta ble
E. Two routes will be installed in the routing table
Refer to the exhibit. Which two statements are true about the partial configuration that is provided.（）
A. The peer group shortens the EBGP configuration
B. The peer group shortens the IBGP configuration
C. All the configured neighbors are in autonomous system 100
D. Three AS - path filters are applied to each BGP neighbor
E. Only the outgoing filters are applied to BGP updates
A. A virtual link to area 0.
B. OSPF summarization command.
C. default - cost extension to the area command.
D. no - summary extension to the area stub comm and.
E. None of the other alternatives apply
A. Interfaces will automatically detect and build adjacencies with neighbor routers
B. DR and BDR elections will not occur
C. DR and BDR elections will occur
D. The neighbor command is required to build adjacencies
E. All routers must be configured in a fully meshed topology with all other routers
A. Down, Init, 2 - Way, Exstart, Exchange, Loading, and Full
B. Down, Init, 2 - Wa y, Exchange, Exstart, Loading, and Full
C. Down, 2 - Way, Init, Loading, Exstart, Exchange, and Full
D. Down, 2 - Way, Init, Exchange, Exstart, Loading, and Full
E. Down, Init, 2 - Way, Loading, Exstart, Exchange, and Full
F. Down, 2 - Way, Init, Exstart, Exch ange, Loading, and Full
最新試題
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Which of the following answers lists a multicast IPv6 address?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）