OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）
A. The ip ospf network broadcast command should be configured on each Frame Relay interface
B. The ip ospf network non -broadcast command should be configured on each Frame Relay interface
C. Th e ip ospf priority value on the spoke routers should be set to 0
D. The ip ospf priority value on the hub router should be set to 0
E. The neighbor command should be configured under the OSPF routing process on all routers
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. During the process of configuring a virtual link to connect area 2 with the backbone area, the network administrator received this console message on R3:
*Mar 1 00:2 5:01.084: %OSPF -4- ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual link but not found from 20.20.20.1, Serial 0 .How should the virtual link be configured on the OSPF routers to establish full connectivity between the areas?（）
A.R1(config - router)# area 0 virtual - link 1.1.1.1 R3(config - router)# area 2 virtual - link 3.3.3.3
B.R1(config - router)# area 1 virtual - link 2.2.2.2 R3(config - router)# area 1 virtual - link 2.2.2.2
C.R1(config - router)# area 1 virtual - link 20.20 .20.2 R3(config - router)# area 1 virtual - link 30.30.30.2
D.R1(config - router)# area 1 virtual - link 30.30.30.3 R3(config - router)# area 1 virtual - link 20.20.20.1
E.R1(config - router)# area 1 virtual - link 3.3.3.3 R3(config - router)# area 1 virtual - link 1.1 .1.1
DR (Designated Router) is for environments where many routers on the same network such as Ethernet. In the following presented network, all routers are reloaded simultaneously, and DR is selected as expected. What is the RTC status?（）
A. 2WAY/DR
B. FULL/DR
C. FULL/DROTHER
D. FULL/BDR
A. show ip ospf interfaces
B. show ip ospf protocols
C. show ip ospf neighbors
D. show ip ospf database
A. less frequent SPF calculations
B. fewer hello packets
C. smaller routing tables
D. reduced LSU overhe ad
E. fewer adjacencies needed
A. show ip ospf database external
B. show ip ospf database nssa - external
C. show ip route ospf
D. show ip ospf datab ase summary
E. show ip route
最新試題
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64