Into which two types of areas would an area border router (ABR) inject a default route?（）
A. stub
B. the autonomous system of an exte rior gateway protocol (EGP)
C. NSSA
D. totally stubby
E. the autonomous system of a different interior gateway protocol (IGP)
F. area 0
您可能感興趣的試卷
你可能感興趣的試題
Router R1 is configured as shown below:
router eigrp 100
network 10.0.0.0
eigrp stub
Based on the information shown above, which two types of routes will be advertised？（）
A. Receive - only
B. Stub
C. Static
D. Summary
E. Connected
F. Dynamic
While troubleshooting an EIGRP routing problem you notice that one of the routers have generated a large number of SIA messages.
What are two possible causes for EIGRP Stuck - In -Active routes?（）
A. Some quer y or reply packets are lost between the routers.
B. The neighboring router starts receiving route updates from this router.
C. A failure causes traffic on a link between two neighboring routers to flow in only one direction(unidirectional link).
D. Th e neighboring router stops receiving ACK packets from this router.
EIGRP performs automatic summarization at network boundaries.
What administrative distance is given to these EIGRP summary routes?（）
A.1
B.90
C.95
D.0
E.5
F.170
G.255
H.None of the other alternatives apply
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command.
Which of the following is true as a result？（）
A.R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1
B.R1 can send IP packets to R2, but R2 cannot send IP packets to R1
C.R2 no longer learns EIGRP routes from R1 for routes not connected to R1
D.R1 no longer replies to R2's Query messages
E.R2n o longer sends to R1 Query messages
Router R1 is three router hops away from subnet 10.1.1.0/24. According to various show interfaces commands, all three links between R1 and 10.1.1.0/24 use the following settings: bandwidth: 1000, 500, 100000 and delay : 12000, 8000, 100.
Which of the following answers correctly identifies a value that feeds into the EIGRP metric calculation？（）
A.Bandwidth of 101,500
B.Bandwidth of about 34,000
C.Bandwidth of 500
D.Delay of 1200
E.Delay of 2010
F.Delay of 20100
最新試題
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Which of the following answers lists a multicast IPv6 address?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）