Refer to the exhibit.
What will happen to traffic within VLAN 14 with a source address of 172.16.10.5？（）
A. The traffic will be forwarded to the router processor for further processing.
B. The traffic will be dropped.
C. The traffic will be forwarded to the TCAM for further processing.
D. The traffic will be forwarded without further processing.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
What will happen when one more user is connected to interface FastEthernet 5/1？（）
A. The first address learned on the port will be removed from the secure address list and be replaced with the new address.
B. All secure addresses will age out and be removed from the secure address list. This will cause the security violation counter to increment.
C. The packets with the new source addresses will be dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
D. The interface will be placed into the error-disabled state immediately， and an SNMP trap notification will be sent.
Refer to the exhibit. The show port-security interface fa0/1 command was issued on switch SW1. Given the output that was generated，
which two security statement are true？ （）
A. Interface FastEthernet 0/1 was configured with the switchport port-security aging command.
B. Interface FastEthernet 0/1 was configured with the switchport port-security protect command.
C. Interface FastEthernet 0/1 was configured with the switchport port-security violation restrict command.
D. When the number of secure IP addresses reaches 10， the interface will immediately shut down.
E. When the number of secure MAC addresses reaches 10， the interface will immediately shut down and an SNMP trap notification will be sent.
Switch R1 has been configured with Private VLANs.
With that type of PVLAN port should the default gateway be configured？（）
A. Trunk
B. Isolated
C. Primary
D. Community
E. Promiscuous
F. None of the other alternatives apply
What is true about access control on bridged and routed VLAN traffic？ （）
A. Router ACLs can be applied to the input and output directions of a VLAN interface.
B. Bridged ACLs can be applied to the input and output directions of a VLAN interface.
C. Only router ACLs can be applied to a VLAN interface.
D. VLAN maps and router ACLs can be used in combination.
E. VLAN maps can be applied to a VLAN interface
On a Company switch named R1 you configure the following： iparp inspection vlan 10-12， 15
What is the purpose of this global configuration command made on R1？（）
A. Discards ARP packets with invalid IP-to-MAC address bindings on trusted ports
B. Validates outgoing ARP requests for interfaces configured on VLAN 10， 11， 12， or 15
C. Intercepts， logs， and discards ARP packets with invalid IP-to-MAC address bindings
D. Intercepts all ARP requests and responses on trusted ports
E. None of the other alternatives apply
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）